1 Answer Hello Terry. NC to COM should read closed and NO to COM should read open. They should reverse when you press the button. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mark January 21, 2015 for Model Number Maytag A8840 My Maytag washer A8840 stopped working when it reached the spin cycle. It now won't work at all but will fill with water, that's it. I looked at the fuse in the lid switch and it's fine, not blown. Could this still be the lid switch?
1 Answer Mark, With the unit not agitating or spinning but filling with water, this would most likely be caused by a faulty lid switch. Read More...
Beth July 26, 2014 for Model Number LAT9206AAM I watched your video, but my washer doesn't open like the one in the video. With mine, you take off the back panel to access the parts. My problem is that I can not reach the lid switch without being able to take the top off like shown in the video. Any suggestions?
1 Answer Beth, To lift the main top on this unit you will need to use a putty knife and on either side of the front of the unit, between the main top and front panel, there are spring clips that you push in on and lift the top. Read More...
Tom June 06, 2013 for Model Number LA7300 My maytag mod LA7300 will fill with water, but will not go into wash or spin unless I drop lid and jar it. What part do I need?
1 Answer Tom, you'll need to test and replace the door switch part number W10820036. Thanks. Read More...
Mary May 22, 2013 for Model Number LSE7804ACE Maytag washer After I open the top lid to reconnect my wires, I realized I indicated the wrong colored wires when I asked my question. The original question is as follows: Copy of your question: "When reconnecting the Lid Switch control - part # 207166, What color wire, "red, white and yellow" goes to what plug? I forgot after I unplugged it." But the colors are actually BLACK, WHITE and ORANGE. I am really forgetful. Thank you for all your support.
Mary May 17, 2013 for Model Number Maytag LSE7804ACE When reconnecting the Lid Switch control - part # 207166, What color wire, "red, white and yellow" goes to what plug? I forgot after I unplugged it.
1 Answer Mary, The White wire will go to the NO on the switch, The yellow will go to the NC and the Red will go to the COM. Read More...
Larry April 28, 2013 When installing new lid switch what terminal does the white, red and yellow wires go to?
1 Answer We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Brian August 12, 2012 for Model Number LAT5005AAE My washer will not go into spin cycle. Would this be the lid switch?
Rob February 01, 2012 for Model Number LSG7806AAE Is there more than one fuse in the washer unit? I replaced the one in the front to the left (if you are facing the washer) and I still get no power. I replaced the lid switch about six months ago. I'm hoping that there is another fuse in the works that might be causing this 'no power' condition. Thanks.
1 Answer Hello Rob. No, there is only on fuse on the washer. You will need to check and see if the unit has power coming to the washer and trace where you are loosing the power at. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Herman September 29, 2011 for Model Number LAT9334 When washing cycle begins after water stops running into tub, if the lid is lifted about half way up water starts to run into tub again and keeps running until lid is lifted all the way up.
1 Answer Hello Herman. Based on the information you provided, it sounds like the pressure switch WP208201 is bad and needs to be replaced. Hope this helps. Read More...