Kathy June 17, 2015 for Model Number CV2136 Need to replace infinite switches on my older Thermador electric cooktop. Can't find BSH00414604 replacements anywhere. Will this switch work, or could it be modified to work?
1 Answer Hello Kathy. The switch needed 00414604 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Dr. Bare January 24, 2015 for Model Number KECS100SOB6 Kitchen Aid cooktop 6" burner control switch is bad. New part no longer available. Will your generic kit AP3109444 fit my unit? If not is there other generic control switch that will work? If you are not able to help do you have contact for me directly to KitchenAid tech support? Thank you
1 Answer Hello Dr. Bare! Yes, the surface unit switch kit W10900107 will work on your model. Thanks. Read More...
Bill January 20, 2015 for Model Number RS6100XKN Will this switch work for my model? My current switch has individual wires not a block. Can the individual wires be attached to this switch?
1 Answer Hello Bill! The universal surface unit switch kit, part number W10900107, will work on your model. Yes, the existing wiring will hook up to this switch. Thanks. Read More...
Ch December 04, 2014 for Model Number RS600BXK1 I installed this surface unit switch and the knob adapter. However the knob still stands too high off the surface of the cook top, even with all but one shaft segments removed. Am I doing something wrong? Otherwise, is there a known best J-rig, like shimming the switch or drimmeling off the adapter shaft? Thanks
1 Answer CH, The shaft segments are approximately 1/8 inch in height. You can remove the total segmented shaft if needed, but your description sounds like that may not work either. Shimming the switch and using a slightly longer screw, sounds like a good alternative, but can't determine what to use as a shim or length of screw. But you don't want the switch assembly to wobble or be loose once it's mounted. Read More...
Sardis H. July 30, 2014 for Model Number RF377PXGQ0 Infinite switch #4391989. Do you have a video for that switch # or wiring detail for this switch as it pertains to the range model #? Thanks
1 Answer Hello Sardis, There is no exact video on this switches wiring since it has a factory change involved. Instructions are as follows: The wire that was on P will go to the pilot terminal on the new switch. The wire that was on the L1 terminal will go to the P2 terminal on the new switch. The wire that was on the L2 terminal will go to the P1 terminal on the new switch. The wire that was on the H1 terminal will go on the terminal labeled 4 on the new switch. The wire that was on the H2 terminal will go to the terminal labeled 2 on the new switch. Read More...
Mike R. May 06, 2014 for Model Number rs6100xkn o I need 3 infinite switches ie. surface switches for my whirlpool range cooktop for 1 large burner and 2 small burners, please let me know if these are available and a price.
1 Answer Mike, both the original 6" and 8" surface elements have been discontinued and replaced with a universal surface element switch, part number W10900107. Thanks! Read More...
James S January 24, 2014 for Model Number RF385PXPN1 I was recommend AP3109444 for my range RF385PXPN1. Reading the description it is a universal switch. That says to me that it is not right for the 5 amp(not big enough) and not right for the 10 amp(too big). I found AP3095444 as a 8.9-11 amp switch the burner is 10-11 amps. The switch that I am replace is KS812700-1 a 10-11 amp switch. Help
1 Answer James, The correct part number for your ranges infinite switch is part number WP3149400. This is for the large burner. If you need the switch for the smaller burners then the part number is WP3148952. Read More...
Arturo September 15, 2013 for Model Number KECC502 Does the surface unit switch 4391989 will work for a dual burner? I am replacing the one that has the 2 burners next to each other, the one in the right back corner of the cooktop.
1 Answer Hello Arturo, You will have to use 8203534. No other switches will work in the application of the right rear dual burner assembly. Read More...
Stanley D. July 15, 2013 for Model Number JHP67G0V7AD Apparently the original part GE WB23X0074 is no longer available. Can part WB21X5243 be used to make the 8 inch and indicator light functions work? It is for the right front element, which normally has 4 inch, 6 inch, 8 inch and girdle functions plus the indicator light? If it can be done can you send a schematic for the electrician to follow? Thanks!
1 Answer Hello Stanley, This part is listed for the other elements on the unit. Since, if you look at the terminal on the element, there are multiple connections, (four), it cannot be used in the place of the original (designed for an element with two terminals). I do apologize for this but, if you were to try to make this work, it could cause an unsafe situation in your home. Read More...
Karen May 24, 2013 for Model Number KECC507 I removed the knobs on my cooktop to wipe it down and while I was cleaning between the knob posts I heard a "pop". Now there is no longer power to my cooktop. I have checked all the GFI switches and checked all my breakers and still no power. Is it ruined or can it be repaired?
1 Answer Karen, You will need to pull the unit and check for power from going to the switches. Also check the terminals on the switches to make sure that there are burnt wires. Read More...