Charles January 20, 2020 for Model Number WGE55S0BW02 Which infinite control switch (far right switch) controls the large burener on this Whirlpool model? Thanks, Charles
1 Answer Hello Charles, the right front burner switch is part WP7403P239-60, for the right rear burner switch the part is WP7403P238-60. Read More...
1 Answer Ronald, as this would vary based on distance, the information can be found during purchase when the shipping information is put in either online or by calling us at 1-877-477-7278. Read More...
Ronald April 10, 2019 for Model Number MERH752BAQ What is the part number for the large unit switch. Also the price?
1 Answer Hello Ronald, the infinite switch for the 8" element is part number WP7403P239-60. Thanks! Read More...
Lone Ranger June 04, 2017 for Model Number Kenmore Dryer Model: 110.85081401 Dryer has 220VAC power present on terminal connector but will not Power ON when control button is pressed. All control buttons are dead.
1 Answer Lone Ranger, You will want to check the control board on the inside of the cabinet and make sure that there is 120 vac to it. If there is then check the wiring harness between the user interface board and the control board and if the wiring checks ok then the control board will likely be the issue. The part number for the board is WP8546219. Read More...
Jim May 31, 2017 for Model Number MER5755QAW will have to know what the number is for on each size switch infinite electric stove burner
1 Answer Hello Jim. WP7403P238-60 is the small element and WP7403P239-60 is the large element. Read More...
Jim May 27, 2017 for Model Number MER5755QAW Infinite switch: part number AP6011291, will this work on all small & Large burner ?
1 Answer Jim, NO, you can't do that. The wattage and amperage differences between the two switches will cause the burners to cycle improperly, if at all. The WP7403P238-60 / WP7403P238-60 is for the small 6" burner element, and the WP7403P239-60 / WP7403P239-60 is for the large 8" burner element for the model number you supplied. You need to install the correct switch to the corresponding element for proper operation. Both parts are in stock and available at this time. Thanks, Read More...
Shawn February 05, 2016 for Model Number CER3520AAH Can you use an infinite switch intended for a large burner on a small burner? Would the amperage be too much?
1 Answer Hello Shawn. No, you can not use a large switch for the small burner. The temp would not be correct and it could damage the element. Read More...
Amy December 30, 2015 for Model Number gge388lxs My front left dual burner has stopped regulating temperature - it is on high whenever it is turned on no matter the temperature I set it to. I found your very helpful video about how to replace the switch. My question is - will this part regulate both the large and the small option for the temperature control? It says it is for a large burner but I would still like to be able to use the small dual also. Thanks in advance~Amy
Beth August 15, 2015 for Model Number WDE101LVQ01 When heating up the oven, the display panel went dark and the oven stopped working. Now the display works only when I turn on the right rear burner to medium and the display comes on. The stove top indicator light does not turn on, none of the four burners get hot, not even the one that turn the display back on and the oven will not go above 100 degrees. When we turn off the right rear burner the display goes dark again. When the display does turn on is says "20" for a couple seconds and then displays the time. I have checked the breaker fuse to be sure that is good and it is. When we took off the control panel we noticed that some of the plastic connectors were burned, the wires are fine. Do we have to replace the infinite switches on all four? Control board? Any help would be appreciated.
1 Answer Hello Beth, This sounds like you have a harness issue and you should pull the tech sheet and use a test meter to troubleshoot since the clock has lost its' ground or neutral and is pulling it from the surface burners' wiring. A good starting place will be the wiring to the burner that you turn on to get the display to light. Also check the door switch circuit since it carries L1 to the control. Read More...
Tom January 30, 2015 for Model Number CRE9600BCE Large burner occasionally goes to full heat, regardless of setting. Is it a bad infinite switch, or the element overheat switch?
1 Answer Hello Tom. It sounds like the switch is bad and will need to be replaced on the unit. Read More...