Kevin December 01, 2011 for Model Number LT7000XVWO How do I replace the lid switch on the washer for a washer/dryer stacked unit. Does the washer cabinet remove the same way as the stand alone washer unit.
1 Answer Hello Kevin. No, on this model, you will raise the lid of the washer and you can access the switch on the side by pulling the tub over to the side. Now you can replace the lid switch W10820036. If the top needs to be removed, you will need to remove the dryer off the washer cabinet. Hope this helps. Read More...
Frank November 17, 2011 for Model Number 11082673810 When I start the wash cycle and pull out the knob, the water does not start to fill the washer all the time. If I wait or reset the start cycle the water sometimes starts to fill and when I get to the spin/rinse cycle the water does not start to fill again but it will spin and or agitate. The door lid has not worked for a long time but the wash cycle would work just fine up to now. Is this something to do with one of the switches or is this a different problem????
1 Answer Hi Frank. You have 2 issues. First the Lid switch is part # 3406. It will not allow start operation or spin. The water valve has inlet scrteens inside the valve. If clogged it will not allow the water incomming. Water valve part# 256937. Thank You. Read More...
Bud November 09, 2011 for Model Number LA612 I have Maytag LA612, Switch Part Number is 2-05415. Is this the same replacement part? The current one has 2 connectors instead of 3. I don't have a meter to test the switch, but when I replaced the switch with a wall switch to test, the machine would spin again. Does this switch acts the same as a wall switch except with a push button? Thanks.
1 Answer Hello Bud. Based on the model number you provided, W10820036 is the correct lid switch. It is used as a safety feature for when the lid is raised on the washer, it shuts the machine off. Hope this helps. Read More...
Gene October 02, 2011 for Model Number LGR6848AZ2 My Whirlpool dryer (LGR6848AZ2 has a broken door switch assembly. What is the best way to get the front of the dryer off to replace the assembly? Thanks
1 Answer Hi Gene. Remove power. Remove lint tray. Remove 2 - screws going from the lint tray cover to the blower hsg. top. Use a putty knife at the top front corners to reach in approx. 3" and push in releasing the tabs that hold the top down. Lift up and support the top. Unhook the door elect. switch connector. Remove the 2- switch mount screws inside the door opening top area. Reassemble in reverse. The part # is W10820036. Thank You. Read More...
Ken September 24, 2011 for Model Number LG7801XMW2 REMOVED OLD-PART #47207 (2-TERMINALS) AND NEED TO REPLACE WITH YOUR NEW PART #AP3094142 (3-TERMINALS) WHAT TERMINALS DO I NEED TO CONNECT TO THERE ARE 3.
1 Answer Hi Ken. The white wire is the common(neutral), #1 terminal /switch. The yellow (board#1-terminal@wh4 conn.) and white(from motor #3 connector) goes to the # 2 N/O on the switch. The gray wire from the lamp goes to # 3 on the switch, N/C connection. Thank you. Read More...
Margrets September 08, 2011 for Model Number Maytag SE7800 How do I open the Maytag SE7800 washer far enough to take a look at the lid switch? Where can I find instructions about how to replace the lid switch?
1 Answer Hello MargretS. You will remove the two screws in the bottom of the front panel and pull the bottom forward and off the machine. You can now access and check the lid switch W10820036. It is located on the right side behind the tub assembly. Hope this helps. Read More...
Ken July 27, 2011 for Model Number LAT8600AAL After installing a new lid switch the machine will only spin? None of the other functions are working.
1 Answer Ken, first off you installed the incorrect part. I would reccomend you order and install WP22001682 the proper lid switch assembly. It'll be less trouble and a lot easier for you. Thanks and Good Luck. Read More...
Boomtown July 10, 2011 for Model Number 11082873820 Can the lid switch have continuity and still be bad?
1 Answer Hello Boomtown. If the lid switch W10820036 shows continuity with the lid closed, then the switch is good. Hope this helps. Read More...
E.J.D July 09, 2011 for Model Number LA7680XM Machine does everything but spin. If it is the lid switch (door switch) and mine has one pin on each side, which pin on the double pin side of the new switch attaches to the wire or is either one ok ? Thanks.
1 Answer Hello E.J.D. You will need to attach it to the one marked NO and the other wire to COM on the switch W10820036. Hope this helps. Read More...
Boomtown July 09, 2011 for Model Number 11082873820 Machine has been operating fine then it stopped agitating or spinning. Do you think its the lid switch? No spin.
1 Answer Hello Boomtown. You will need to test the lid switch W10820036 and see if it is good. It should read closed with the lid closed for continuity. If not, you will need to replace the lid switch. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...