John June 03, 2012 for Model Number 110.81675110 Machine works great when I leave the lid open. it washers. drains, spins. but when I closed the lid , the machine wont do anything. It is like a reverse switch.
1 Answer Hello John. On the end of the switch where there is two spades, you will need to remove that wire and hook it to the other spade. You have the switch W10820036 wired wrong. Read More...
Dogboy May 28, 2012 for Model Number la5668xtwo Washing machine won't drain at the end of the cycle; what's wrong with it?
1 Answer Hello Dogboy. You will need to check and see if the lid switch W10820036 is bad on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Sam May 16, 2012 for Model Number kawe55lov Do I have to remove the top to replace the lid switch? I can't seem to get it lined up to screw it back in?
1 Answer Hello Sam. It is easier to replace the switch W10820036 if you remove the cabinet from the frame of the unit. Disconnect the power to the unit. Remove the two screws in the back corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and replace the lid switch. Reinstall in reverse order. Read More...
Trudy April 30, 2012 for Model Number 110. 66912691 MH1877776 When you push the start button there is a click sound then nothing. After I open the door and push the door switch close the door the start button will make that click noise then nothing. I the door switch bad? Do I need this part?
2 Answers Hello Trudy. You will need to test the thermal fuse WP3390719 located on the top of the blower wheel housing. It should read closed for continuity. It does not sound like the door switch. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Trudy April 30, 2012 for Model Number 110. 66912691 MH1877776 When you push the start button there is a click sound then nothing. After I open the door and push the door switch close the door the start button will make that click noise then nothing. I the door switch bad? Do I need this part?
2 Answers Trudy, The door switch could have failed, but your first check should be to make sure you have 220 to 240 VAC at the terminal block on the back of the dryer, try this, check and reset the breakers for the dryer,in the breaker box, several times. Then unplug the dryer cord and remove the line cord cover panel on the back of the dryer and make sure the terminal nuts are all tight and there are no damaged wires. Good Luck and Thanks Read More...
Bob R. April 04, 2012 for Model Number maytag #A482 Does the door switch also control the out of balance shut off and if so what parts needs to be replaced? Is it the kit #ap3094142?
1 Answer Hello Bob, On the older models such as this one the lid switch WP691581 did also control the out-of-balance. The unit has a lever that requires that the lid switch bracket be adjusted to the point that the lid can only be opened approximately an inch before the switch shuts down the units' operation. This allowed the lid switch and the micro switch to both be properly adjusted for normal operation. If you refer to the wiring diagram, it explains this much better than I can explain. You need to be sure before you order which switch is giving the problem. Sometimes the switches aren't giving a problem and the problem can be corrected with a door switch bracket adjustment. Let us know if we can assist further. Read More...
Bob March 18, 2012 for Model Number lat8214aae The lid fell off an we found the two balls but it still will not come on after filling up. Is the something the door pushes in to turn the safety switch on?
1 Answer Hello Bob. The lever WP22001311 pushes the lid switch and turns on the washer. Hope this helps. Read More...
Ken March 13, 2012 for Model Number matag lat9700aal My washer will not add water but will spin and drain. It will not fill on rinse but it will spin on final and shut off.
1 Answer Hello Ken. First check to see if the water has been turned off. Then try setting the water temperature to warm or hot. If it fills at this setting you have a bad water inlet valve 205613. If it doesn't fill, you either have a bad pressure switch WP207360 or a bad timer 207373. Hope this helps and have a great day! Read More...
John December 09, 2011 for Model Number LA5580xtno Machine start washing but it won't drain or spin it stop.What could be the problem
2 Answers Hi John. Has the lid switch actuator broken and not engaging the lid switch ? The actuator is part # WP359807. If the lid switch is not making contact it is part # W10820036.You can momentarily jump these 2-wires together with electrical tape to test. Check the cold water side of the water valve to see if the screen is clogged not letting the water in. If so it is part # 285805. Thank You. Read More...
John December 09, 2011 for Model Number LA5580xtno Machine start washing but it won't drain or spin it stop.What could be the problem
2 Answers John, you're on the right track, with a faulty lid switch the washer will fill and wash, but it won't drain or spin. W10820036 you should be able to hear the switch " click" when you raise and close the lid, also check the actuator lever WP359807, make sure it has not been damaged or broken. Thanks and Good Luck Read More...