Joes Do November 18, 2019 for Model Number WFW9200SQ01 full load machine stop after 15 minutes, and cod F20 show up, I cancel the cycle . restart it , it works fine . but used less water than before. when I do half load , the machine works good. why is that? thanks
1 Answer Joes do, First, check and flush the faucets check and clean the hose screens and fill valve screens are clean and free of any debris or sediment. Then disconnect the air tube from the water level switch and check for twists, kinks, and clogs in the tube(blow into the end of the tube to make sure). Then check the wires between the water level switch and the main control board(CCU). The flow meter isn't a likely issue, but you could also check for debris or hard water deposits built up on the internal surfaces of the inlet/outlet tubes. Read More...
Aaron August 06, 2014 for Model Number MHWE300VW00 When I run the washer with hot/cold rinse water the drum fills to a level about 1/4 the way up the door on wash but barely wets the clothes on rinse. However when I run the washer in cold/cold the washer barely wets the clothes in wash mode and in rinse mode. So, I have concluded that I must have a problem with the cold water supply. What components could effect this? I have already blown 50 bucks on a pressure switch which didn't help.
1 Answer Aaron, The firs thing that you will want to check is the screen on the water valve. The screen is most likely clogged up causing a slow flow from the cold water. If this checks ok then the issue would be in the valve. Read More...
Mark March 15, 2014 for Model Number WFW9200SQA12 Where does the pressure hose connect from the pressure sensor down to where?
1 Answer Mark, The pressure hose connects from the pressure sensor down to the side of the tub to a air dome on the side of the tub. Read More...
Blair June 28, 2013 for Model Number WFW9200SQA12 In my previous question regarding the F20 error you mentioned that it might be a kink in the air dome. Can you identify that part for me or tell me where to look? Thanks.
Blair June 28, 2013 for Model Number wfw9200sqa12 We keep getting intermittent F20 error codes. When we restart the cycle it runs fine for 2 or 3 loads and then we get F20 again. I have checked water flow in and and cleared all of the drains going out. I am leaning towards the pressure regulator (W10163982). Is there a way to test it before I spend $50 - $70 for a new one? Do you have any other suggestions? Thanks.
1 Answer Blair, The best way to test the pressure switch is by putting the unit into a diagnostic cycle. This information is on the tech sheet on how to put into diagnostics. What this sounds like is maybe a kinked or clogged pressure hose or air dome. Make sure that the screens in the water valve are also clean. Read More...
Larry T August 27, 2012 for Model Number Whirlpool Washer WFW9200SQA12 Water level seems very low. Hardly any water in washer. Is this water level switch adjustable? What is the water height supposed to be and how do you measure it? Cloths seem to come out clean, but just no water in the machine.... THanks for any assistance...
1 Answer Hello Larry. The water level in this washer should be low and the switch W11417622 is not adjustable. This machine is designed to run with little water being used. Read More...
Mike Fowler March 14, 2012 for Model Number MHWE300VF00 What does this switch do and can it cause F-28 errors. It appiers to be loose and free to swing around.
1 Answer Hello Mike. W11417622 is the pressure switch and is used for the water level. Here is what the manufacture recommends for the F-28 code. 1. Unplug washer or disconnect power. 2. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). – Check connections of the CCU board within the housing. – Make sure all grounding switches are engaged. 3. Check the drive system for any worn or failed components. 4. Plug in washer or reconnect power. 5. Verify CCU operation by running a Diagnostic Test or any cycle. 6. Check the MCU by looking for operations of the drive motor. 7. Check that the serial harness at the MCU is not mounted upside down. The wires should be to the left when facing the MCU connectors. If the CCU is new, and the motor and wires are good, then the MCU WPW10384846 is bad and will need to be replaced. Hope this helps. Read More...