Miguel March 08, 2016 for Model Number MHWE200XW00 Do you have a diagram to show cold water hose connections from the valve, when installed, to the dispenser? I read the prior answer but my wife thinks originally the hoses looked cris-crossed meaning: 1) The upper valve hose connects to the far left dispenser feeding the soap. 2) The lower valve hose connects to the middle dispenser feeding the softener. The valves are not labeled to show if feeds to soap or softener dispenser. Right now, I believe this is correct configuration as when I turn on a wash cycle, the soap tray fills up First with water. Thank you.
1 Answer Miguel, Unfortunately we do not have a diagram showing how the hoses go but it does sound like you have the correct configuration. Read More...
Michele November 10, 2014 for Model Number W10202596 What is the size of the screw that holds this valve contraption onto the back of the washer? Thanks
1 Answer Hello Michele. Sorry, we do not have the size of the screw for the valve. This may vary by the model number of the unit. Read More...
Frank July 24, 2014 for Model Number MHWE200XW00 Maytag washer will not dispense liquid bleach in any or proper mode. It does dispense liquid liquid soap. Thanks.
1 Answer Frank, At the first rinse you will want to check to make sure that the unit is sending power to the water valve and make sure that water is coming through. It is possible that the nozzle is clogged and not allowing water to enter. Read More...
Pat March 30, 2014 for Model Number MHWE250XL00 On the Maytag drawing of the dispenser parts (parts W10315510 page 5), they show that the left valve of the dual valve goes tot the middle inlet of the dispenser and the right valve on the dual valve goes to the right inlet of the dispenser. When i do that, i note that the water goes in the right side (softener compartment) when its time to wash and vice versa, so the water goes on the left side in the detergent part when its time to rinse! My question is : Can you tell me if the maytag drawing is ok or not! If its right, the problem should be the valve? Just for information, i took off the valve to take a look at it because some morning last week water flowed through the door and water level was very high. So The code error F8E3 was flashing on the washer display! Thank you! Hope that my english is clear because i'm french
1 Answer Pat, The way that the hoses are set up are as follows. The single valve will go to the far right of the dispenser is you are looking at it from the back. The dual valve right side will go to the middle and the other will go to the far left. Read More...
My N. March 11, 2014 for Model Number WFW9151YW The bleach on my washer is not dispensing correctly. Which valve and/or nozzle will correct this issue?
1 Answer Hello My, The tech sheet directs to do the following in this order: 1. Verify the washer is level. 2. Verify dispenser drawer is not clogged with detergent. 3. Check water hose connections to the washer and within the washer. Check for plugged screen in water source. 4. Check the water supply and the water valve. 5. Verify washer operation by running a Service History Mode & Diagnostic Test. This is all explained on the units' tech sheet. This is usually located in a plastic bag behind the kick panel. The fault codes are also explained fully on the tech sheet. Read More...
Giang N August 31, 2013 for Model Number WFW9150WWOO I have whirlpool washer the problem in the dispenser this not working for softener can you show me what problem and how to fix this thank you too much.
1 Answer Giang, Verify the washer is level. 2. Verify dispenser drawer is not clogged with detergent. 3. Check water hose connections to the washer and within the washer. Check for plugged screen in water source. 4. Check the water supply and the water valve. 5. Verify washer operation by running a Service History Mode & Diagnostic Read More...
Dennis S. March 04, 2013 for Model Number WFW9250WWOO I am getting the LF error code, turned off and unplugged as manual recommended, but it countiues. Is this an indication that the inlet valve needs to be replaced. Whirlpool front loader is about 2.5 years old.
1 Answer Hello Dennis. Yes, if the unit is filling slow and is throwing an LF code, it could be the valve. Make sure the screens are not clogged on the unit. If not, and it fills slow, replace the water valve on the unit. Read More...
Rhonda R. June 12, 2012 for Model Number whirlpool washer wfw9150wwoo The valve part # ps 2366737 is leaking water. Not the hose attached to it the part. What would make this happen the washer is on 2 yrs 6mos old.
1 Answer Hello Rhonda. The valve WPW10212596 has gone bad on the unit and will need to be replaced. Sometimes these go out quicker than others do and need to be replaced. Read More...