1 Answer Hello Dave. NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. If after 30 seconds not minimum 0.1l of water entered or maximum fill time of 16 minutes is exceeded, the valves will be turned off and the error code will be displayed. Press PAUSE/CANCEL twice to clear the display. Read More...
Jennlynn June 25, 2012 for Model Number GHW9150PW0 Hello, is this the right intake valve for my older model #? Thanks!
1 Answer Hello Jennlynn! The water inlet valve for your model GHW9150PW0 is part number WP8181694. Thanks! Read More...
Deer June 09, 2012 for Model Number ghw9300pw4 when turing on washer keep running washer no water is coming. do I need a new valve? thanks
1 Answer Deer, If the washer runs properly but has no water, your first check should be the water level switch and tube WPW10514214, WPW10004260 but at the swame time you ought to have some form of error code ( F2,F9,FH, etc.) in the display ? We'll send you some information, so you can test the control, run component tests and codes. Thanks Read More...
Adrianne B April 29, 2012 for Model Number MW9600SQ1 I am purchasing a water inlet valve and would like a diagram and / or any instructional help you can provide for replacing the part please.
1 Answer Adrianne, here are the instruction for a MFW9600 washer : "1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. disconnect the hoses from the fill valve 3. Remove the top cover and the console 4. Disconnect the two wire connectors from the inlet valve terminals.5. From behind the washer, remove the inlet valve screw, then slide the valves to the right and unhook them from the panel, and remove them. 6. Loosen the clamp and disconnect the hose from the water valves. Top Removal : 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the three T-20 hex-head torx screws from the top cover of the washer on the cabinet back. 4. Pull back on the cover and release the tabs in the console from the slots in the cover, then lift the cover off the unit." Good Luck and Thanks Read More...
Sam March 26, 2012 for Model Number ghw9300pw4 My washer filled up with water when not in use and overflowed when I opened the door. I saw water draining into the tub from the water inlet at the top. I'm trying to make sure that this is the part I need. Thank you!
1 Answer Hello Sam. Yes, based on the information you provided, it sounds like the water valve WP8182862 is bad and will need to be replaced on the unit. Hope this helps. Read More...
Steve March 06, 2012 for Model Number GHW9150PW4 There is water in the tub if the washing machine has not been used recently. Is this a bad inlet valve? Thanks
1 Answer Hello Steve. Yes, based on the information you provided, it sounds like the water valve WP8182862 is bad and will need to be replaced. Hope this helps. Read More...
Rickey December 21, 2011 for Model Number DO NOT KNOW FOR SURE I have maytag front load washer in 3000 series performance. Please what model no. Does this fit? It looks like mine. Water inlet valve no. Ap3955809.
1 Answer Hi Rickey. Double check the model # on the back of the control panel. The MAH3000AWW water valve is part # WP22002903. Thank You. Read More...
Krister December 21, 2011 for Model Number wfw9200sq00 When turning on washer, it makes a stuttering kind of knocking noise coming from behind the dispense. No water is coming through dispenser. Do I need a new valve? Thanks!
1 Answer Krister, You're on the right track, The water valve WP8182862 would be the best place to start. Also remember to flush both faucets and clean the debris from the fill hose screens, and You'll be fine. Thanks and Good Luck Read More...
Chincey August 06, 2011 for Model Number GHW9150PW4 I have seen both of the water inlet valve parts listed above on this thread as being the valve for my machine....perhaps versions -PW1-3 have a different part number then my version -PW4? Can you confirm that AP3955809 (Manufacturer's Number: 8182862) is the correct part for my machine Whirlpool GHW9150PW4? Thanks.
1 Answer Hello Chincey! The water inlet valve used on your Whirlpool Washer model GHW9150PW4 is part number WP8182862. Thanks! Read More...
Dain C. June 21, 2011 for Model Number GHW9150PW4 Water keeps running into my washer even when not in use. Is this most likely because the water inlet valve (part # AP3955809) needs to be replaced or is there other things I should be checking first? My washer is about 8 years old.
1 Answer Hello Dain! Yes, the water inlet valve seems to be defective and will need to be replaced. Your part number is WP8182862. Thanks! Read More...