Parts for Ge ZV54ISH2SS: 01 - Range Hood Parts

This replacement junction box cover protects the appliance's electrical junction box and helps keep wiring secure and free from damage. It restores a finished, safe enclosure for power connections. What it does:

• Covers and protects the junction box where the appliance wiring connects to the terminal block
• Keeps wiring and terminals shielded from debris and accidental contact
• Helps prevent electrical shorts and reduces risk of exposed live parts
• Commonly replaced if cracked, missing, or when servicing the terminal area

• One junction box cover

• Always disconnect power to the appliance at the breaker or unplug before servicing
• Remove mounting screw(s) and old cover, then align and secure the replacement cover with the original hardware
• Verify the cover seats fully and that all wires are routed inside the junction box before restoring power

This motor start/run capacitor helps the appliance motor start and run smoothly, restoring proper motor performance and reducing strain. Replace a failing capacitor to address motor start problems and intermittent operation. What it does:

• Provides the electrical boost motors need to start and maintain RPM
• Helps prevent motor hesitating, sluggish starts, or failure to start
• Can reduce motor overheating and tripping caused by poor starting torque
• Works with the motor's electrical circuit to stabilize operation during run cycles

• Always disconnect power to the appliance before servicing.
• Discharge the capacitor before touching terminals to avoid shock.
• Match wiring and terminal orientation to the original part; secure connections tightly.

The GE Filter, Baffle is an OEM part for GE range hoods. This baffle filter plays a role in maintaining clean air in your kitchen by trapping grease and other particles that arise during cooking. Its design not only improves ventilation but also helps protect the range hood's motor and interior components from damage caused by grease buildup.

Regular maintenance, including cleaning and, when necessary, replacement of the baffle filter, is essential to keep your range hood working efficiently. Over time, filters can become so saturated with grease and debris that they cannot be effectively cleaned, necessitating replacement.  

Symptoms of a bad GE Filter, Baffle include:

• Decreased airflow or efficiency in venting smoke and odors out of the kitchen.
• Visible grease buildup or damage to the filter, indicating it's no longer functioning properly.
• Unusual noises from the range hood, which can be caused by air struggling to pass through a clogged or damaged filter.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This baffle filter is made for use with range vent hoods. It's one of the most efficient filters for a range. The part is made of stainless steel and helps maximize grease filtering and airflow when the hood is powered on. As air hits the baffles, it changes the direction to collect debris in the baffles of the filter.In many cases, cleaning the baffle filter will offer additional longevity. However, these components will sometimes need to be replaced. This is typically required if the baffle filter has experienced damage. Basic tools may be required to make the replacement. A pair of work gloves can also be useful for protecting the hands during the process. Make sure the range vent hood is powered off and cool to the touch before replacing this part. The original part will need to be removed from the vent hood before the new model is installed.This is an authentic OEM replacement part that is designed for use with General Electric range vent hoods. The baffle filter is directly sourced from the manufacturer and priced on an individual basis.

The Halogen Light Bulb is an OEM part for GE range hoods. It provides bright, focused illumination to enhance visibility while cooking, ensuring a well-lit stovetop area.

Causes of a bad halogen light bulb can include burnout from extended use, exposure to high temperatures, or damage from electrical surges. Additionally, oil and residue from frequent cooking can accumulate on the bulb, potentially leading to overheating and failure.

Symptoms of a bad halogen light bulb include:

• The light not turning on
• Flickering or intermittent lighting
• Dim or insufficient light output
• Blackened or visibly damaged bulb

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This lampholder is the light socket that secures the bulb and delivers power so your appliance lighting works reliably. Replace a worn or heat-damaged socket to restore steady illumination and dependable operation.

• Provides secure mounting and proper electrical contact for the light bulb
• Fixes issues such as no light, flickering, or bulbs that won't stay seated even after replacement
• Replaces sockets with visible cracks, discoloration, or burned contacts
• Uses the bulb type and wattage specified for your model

• Disconnect power at the breaker or unplug the appliance before servicing
• Use only the bulb type and wattage listed for your appliance; seat the bulb fully without overtightening
• Transfer any mounting screws, bracket, or connectors from the original part as required by your model

This transformer kit replaces a failed power transformer in your microwave, restoring the correct output to the high-voltage circuit so the magnetron can generate heat and the oven operates reliably. What it does:

• Steps up incoming line voltage to the high voltage required by the magnetron
• Supplies power to the microwave's high-voltage circuit during cooking
• A failing transformer may cause no heat, loud humming/buzzing, a blown internal fuse or tripped breaker, or a burning odor
• Used when the original transformer tests shorted/open or shows signs of overheating

• 1 transformer kit assembly

• Disconnect power before servicing; microwave high-voltage components can retain a dangerous charge—properly discharge the capacitor
• Transfer brackets/wiring exactly as originally routed and secure all terminals firmly
• Inspect the high-voltage diode and capacitor; replace if damaged or if no-heat persists after installation

This blower assembly replaces a worn exhaust blower to restore proper venting and airflow in the appliance. It mounts in the blower chamber and circulates air to remove steam, smoke and odors. What it does:

• Spins the blower wheel to move exhaust air through the vent system
• Restores weak or no airflow from the appliance
• Stops or reduces loud or irregular blower noise when worn bearings are the cause
• Helps prevent moisture buildup and lingering cooking odors

• Disconnect power to the appliance before starting any work
• Remove outer panels or grille to access the blower housing; keep fasteners organized
• Disconnect wiring harness and motor connectors before removing the old assembly
• Blower wheel spins freely and electrical connections are secure after installation

This lamp holder support secures the appliance's light socket in the proper position so your lighting stays steady and reliable. Replace a cracked or heat-damaged support to keep the bulb and wiring stable and the work area/interior well lit.

• Holds the lamp socket/holder firmly in place to prevent movement and vibration
• Helps restore consistent lighting when the bulb and fuse test good
• Common symptoms: light flickers or cuts out when the door is used or when bumped
• Visible signs include broken tabs/clips, warping, or heat damage on the support

• Disconnect power and allow the appliance to cool before servicing
• Access the lamp area by removing the appropriate cover or panel as directed by your service manual
• Transfer the socket and wiring to the new support; avoid pinching or straining wires
• Handle bulbs with care and test operation before reassembly

This indicator light is a replacement panel lamp that shows oven or cooktop status so you can quickly see when a function is active. It restores visible status feedback on the control panel. What it does:

• Illuminates to indicate oven, bake, broil, or timer status so you can tell when a cycle is running
• Provides a clear visual signal from the control panel or console
• Replaces a cracked, burned-out, or non-lighting indicator to restore normal feedback
• Matches the OEM fit and function for compatible GE control panels

• Disconnect power to the appliance before starting any repair to avoid shock
• Remove the control panel or console trim to access the indicator—retain fasteners and orientation for reassembly
• Handle the lens and bulb with care; replace only with the exact part number shown

This motor/lamp switch is the user control for many GE range hoods. It turns the fan motor and hood light on and off, restoring reliable control when the original switch becomes worn, intermittent, or sticks.

• Provides on/off control for either the hood fan motor or the hood light, depending on model location
• Common symptoms: fan or light won't turn on, stays on, intermittent operation, or a loose/sticky rocker
• Restores reliable, positive switching of the selected circuit
• Direct-fit replacement designed for the original switch footprint

• Disconnect power at the breaker before servicing
• Remove filters and the control/trim panel to access the switch (procedure varies by model)
• Photograph or label wire positions; transfer one lead at a time to the new switch
• Seat the switch fully in its bracket, reassemble, restore power, and test operation

This knob assembly is a genuine OEM replacement part that is found on range hoods. The knob is used to turn the power off and on to the fan and light. This knob is made of durable plastic, but it may crack and break over time. If this happens, it isn't easy to turn the shaft to the off and position that powers the fan and light. When the knob is damaged, it should be removed and replaced with a new one. Tools are not required to remove and replace the knob. To start, disconnect the range hood from the outlet or turn off the breaker. Grasp it tightly and pull hard. The knob will pop off. Line the new knob up with the slot and push it in place. Restore the power to the range hood.This knob assembly is a black plastic molded part sold individually. It is designed for range hoods manufactured by General Electric.

The Control Knob is an OEM part for GE ranges. This part allows you to select and adjust the desired temperature or cooking function for the oven or cooktop burners.

Causes of a bad knob can include wear and tear over time, accidental impact or damage, or potential issues with the control stem or mechanism it connects to.

Symptoms of a faulty control knob include:

• Difficulty in turning or adjusting the knob
• Knob feeling loose or wobbly
• Markings or numbers worn off or illegible
• Knob not properly engaging with the control stem

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bezel is a small trim piece that finishes an opening on the appliance's control area. It restores a clean, factory look and helps protect the underlying panel when the original is cracked, loose, or missing.

• Frames the control opening for a finished appearance
• Helps shield panel edges from wear and debris
• Typical symptoms: cracked plastic, broken tabs, discoloration, loose or missing trim

• Disconnect power and allow the appliance to cool before servicing
• Remove any adjacent knob or trim as needed for access
• Release the old bezel's tabs or screws and note its orientation
• Install the new bezel in the same position, then reinstall removed parts and test

This bottom filter support panel holds and secures the refrigerator's water/air filter assembly at the cabinet base, helping maintain proper filter alignment and stable operation. Replaces a cracked or missing support to restore correct filter seating. What it does

• Supports and positions the refrigerator's bottom-mounted filter housing for proper filter engagement
• Prevents the filter from shifting or falling, which can cause leaks, noise, or poor water/ice quality
• Restores a stable mounting surface after damage, wear, or during filter replacement
• Uses existing fasteners and mounting points—no additional brackets required

• One bottom filter support panel

• Turn off water supply and unplug the appliance before starting work
• Remove the lower access panel or kickplate to reach the filter area; keep track of mounting screws
• Inspect surrounding seals and filter housing for damage when installing the new support