Range Pilot

This thermocouple sits in the pilot flame and signals the oven safety valve that a flame is present. Replacing a weak or open thermocouple restores safe ignition and consistent burner operation on standing-pilot gas ranges.

• Detects heat from the pilot flame and generates a small millivolt signal to allow the oven safety valve to remain open
• Common symptoms of failure: oven won't heat, burner lights then goes out, pilot won't stay lit, intermittent oven shutdown
• Confirms flame presence to help prevent unlit-gas flow during operation
• Intended for standing-pilot style gas ovens/ranges

• Disconnect power and shut off gas before servicing; allow the appliance to cool
• Route and secure the new thermocouple exactly like the original; avoid sharp bends and kinks
• Position the tip correctly in the pilot flame; hand-start threads and snug fittings—do not overtighten
• After installation, check all connections for leaks with a soap-and-water solution and verify proper burner operation

This pilot burner supplies the standing pilot flame for the right-side surface burners on standing-pilot gas ranges. Replacing a clogged or damaged pilot restores consistent ignition and a stable flame for reliable burner lighting.

• Provides the small, continuous flame that lights the right-side surface burners when their valves are opened
• Helps maintain correct pilot flame size and positioning for dependable crossover ignition
• Safe symptom clues: pilot won't stay lit, weak/yellow flame, intermittent or no lighting of the right-side burners, needing a match to light
• Physical damage or blockage from spills/debris can impair operation

• Disconnect power and shut off gas before servicing; allow the appliance to cool
• Access the pilot area; note routing and orientation before removal
• After reconnecting, check all gas connections with an approved leak-detection solution
• Adjust the pilot flame to manufacturer specifications and re-light pilots as required

This oven pilot assembly with thermocouple maintains a steady pilot flame and proves flame presence to the safety valve so the oven burner can ignite and stay on. Replace when the pilot won't hold or oven ignition is inconsistent.

• Supplies the constant pilot flame needed to light the oven burner
• Thermocouple sends a flame-present signal to allow/hold gas flow to the burner
• Helps resolve issues like the pilot going out, burner not lighting, or oven shutting off mid-cycle
• Restores consistent oven ignition on pilot-equipped models

• Shut off gas supply and power; allow the appliance to cool before servicing
• Note routing and mounting before removal; install the new assembly in the same orientation
• After reconnecting lines, check all joints for leaks with an approved leak-detection solution
• Verify a stable pilot flame and proper burner ignition after installation

This pilot burner supplies the small, continuous flame that lights the surface burners on gas ranges/cooktops, helping ensure reliable burner ignition and steady performance.

• Provides a steady pilot flame to ignite the surface burners
• Helps restore lighting when surface burners won't ignite or the pilot won't stay lit
• Can address weak or inconsistent pilot flame at the top burners
• Typical signs include repeatedly having to relight the pilot or burners going out during use

• Disconnect electrical power and shut off gas before servicing
• Allow the appliance to cool and ventilate the work area
• Inspect and clean mating surfaces; replace brittle tubing or cracked fittings as needed
• After installation, check for leaks and adjust the pilot flame per the service manual

This pilot burner assembly ignites the oven's main burner and restores reliable pilot flame control for gas ranges and ovens. Use to replace a worn or malfunctioning pilot that won't hold a steady flame. What it does:

• Provides the small, continuous pilot flame required to light the main burner
• Helps resolve symptoms like a weak or out pilot flame, intermittent ignition, or oven that won't light
• Direct replacement for the OEM pilot burner assembly designed for compatible gas ovens
• Works with factory gas control and ignition components when installed correctly

• Turn off gas supply and electrical power to the appliance before servicing
• Inspect the gas orifice and pilot tube for debris; clean gently if needed
• Use appropriate hand tools and tighten fittings to manufacturer torque specs — do not overtighten

This pilot thermostat is the oven temperature control that senses heat and helps regulate burner operation for consistent cooking. It replaces a worn or faulty thermostat to restore accurate temperature response and reliable oven ignition. What it does:

• Senses oven temperature and signals the burner/pilot system to maintain set heat levels
• Helps the oven light and hold temperature when the pilot or main burner is used
• Commonly used when the oven won't heat, cycles excessively, or fails to maintain consistent temperature
• Works as the temperature-sensing control element in gas oven pilot systems

• One pilot thermostat

• Turn off power and shut off gas supply before starting any service
• Handle thermostat gently; avoid bending or stressing the sensing element or capillary tube
• Verify wiring connections match the old part; replace like-for-like