Range Guard, Shield, Barrier Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This guard terminal protects and shields wire connection points on your appliance, helping prevent accidental contact and shorting while keeping terminals organized for reliable operation. What it does:

• Covers and insulates exposed terminal connections to reduce risk of arcing or short circuits
• Keeps wiring routed and separated for consistent electrical contact
• Helps avoid accidental contact during maintenance or part replacement
• Supports safe operation by protecting fragile terminal ends from bending or snagging

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Replace only with the correct terminal guard
• Use basic hand tools; avoid bending terminals or over-tightening fasteners

This lower heat shield is a stamped metal shield that protects the oven's lower cabinet area and surrounding components from excessive heat. It helps maintain safe operation and reduces heat transfer to nearby parts. What it does:

• Shields the oven's lower cavity and insulation from direct heat
• Prevents heat-related damage to the range cabinet and nearby components
• Can reduce hotspots that cause smoking or burning odors
• Restores proper airflow and clearance under the oven when damaged or missing

• One lower heat shield

• Disconnect power (and gas, if applicable) before servicing the appliance
• Remove oven drawer and access panels to reach and replace the shield
• Use gloves to protect hands from sharp metal edges during installation
• Tighten fasteners securely but do not overtighten—replace any damaged mounting hardware

A replacement protective shield that covers and protects internal appliance components from debris, moisture and incidental contact. Restores protection to damaged or missing shields to help maintain safe, reliable operation. What it does:

• Covers and protects wiring, connectors or nearby parts from accidental contact and debris
• Helps prevent moisture or food particles from reaching sensitive components
• Replace if the shield is cracked, warped, missing or allows exposed parts
• Reduce rattles or contact-related noises caused by loose or damaged shields

• Shield

• Disconnect power to the appliance before starting any repair
• Use care around sharp edges; wear gloves and eye protection
• Remove fasteners holding the old shield; reuse or replace screws as specified by the manufacturer

This heat shield protects the area beneath the cooktop/oven from heat and accumulated spills, helping prevent damage to nearby components and simplifying cleanup. Designed to fit in the original mounting location. What it does:

• Deflects and dissipates heat away from sensitive components and cabinetry
• Catches and channels spills or drips away from burners and electrical parts
• Helps reduce risk of scorched surfaces and heat-related discoloration
• Restores proper clearance and protection after removal or damage

• Disconnect power (and gas, if applicable) and allow the appliance to cool completely before starting
• Handle carefully; edges may be sharp and mounting tabs can be fragile
• Verify correct orientation and secure mounting per manufacturer instructions

A replacement shield that protects internal refrigerator components from damage and keeps nearby parts securely covered. Replaces a worn or cracked cover so panels and wiring stay shielded during normal use. What it does:

• Covers and protects vulnerable components from accidental contact and debris
• Helps maintain proper clearance between parts to prevent rubbing or interference
• Restores a finished appearance where the original shield is damaged
• Useful when the original cover is cracked, broken, or missing

• Always unplug the appliance or shut off power at the breaker before servicing
• Handle the part carefully to avoid sharp edges and to prevent further damage
• Basic tools (screwdriver or nut driver) may be required for removal and installation

This replacement shield is a molded protective mounting shield that helps protect internal appliance components from debris and physical damage, keeping parts aligned for reliable operation and quieter performance. What it does:

• Covers and protects wiring, harnesses, or small components from contact and debris
• Helps maintain proper alignment of nearby parts to reduce wear and noise
• Prevents incidental interference between moving parts
• Restores intended component protection after damage or removal

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Handle plastic tabs and mounting points carefully to avoid breaking clips
• Reuse original fasteners if undamaged; replace any broken clips before powering appliance

This metal angle flue guard protects and covers the flue opening on compatible gas ranges, helping direct exhaust and keeping nearby components shielded from heat. It restores the range's original flue trim and helps maintain safe operation. What it does:

• Replaces a bent, cracked or missing flue guard that no longer shields the flue opening
• Directs heat and combustion byproducts away from surrounding panels and components
• Helps reduce hot spots and contact with wiring or insulation near the flue area
• Restores proper fit and appearance of the cooktop/flue assembly

• One angle flue guard

• Turn off and disconnect power and gas supply before starting any repair
• Remove cooktop or access panels as required to reach the flue; retain original fasteners unless new ones are supplied
• Handle edges carefully; metal trim may be sharp