Parts for Speed Queen FEU17AWF1702: Rear Bulkhead Parts

A clear silicone adhesive/sealant used to bond and seal appliance trim and components, helping restore watertight and stable assemblies. Supplies a durable, flexible hold for small repairs where factory adhesive is specified. What it does:

• Bonds trim, panels, and small plastic or metal parts to prevent movement and leaks
• Seals gaps to reduce water intrusion around housings and door areas
• Provides a flexible, durable hold that resists vibration and temperature changes
• Useful for reattaching trim, tabs, and molded parts when original adhesive has failed

• One (1) clear 3 oz tube of DOW 737 adhesive

• Use in a well-ventilated area; wear gloves and eye protection to avoid skin/eye contact
• Surface must be clean, dry, and free of oils or old adhesive for best adhesion
• Apply as a thin, even bead; allow recommended cure time before reassembling or using appliance
• Follow any OEM repair instructions and local disposal guidance for adhesive containers

This seal kit restores a proper water-tight barrier in the washer's drive area to prevent leaks and protect bearings and motor components on 1992-and-newer units.

• Seals the drive shaft/tub interface to stop water migration
• Helps prevent bearing and motor damage from moisture
• Common leak symptoms: water under the washer, rust streaks at center post, noisy spin from moisture intrusion
• May also address oil/water contamination around the transmission area

• Disconnect power and water; move the washer to a stable, level work area
• Removal of agitator, inner tub, and drive components is typically required
• Inspect shaft and mating surfaces; clean and lightly lubricate as specified by service literature
• Use proper drivers/press tools; do not hammer seals into place

This rear bulkhead assembly with seal replaces the washer's rear tub enclosure to restore a watertight connection and support the drum. It prevents leaks and helps maintain proper tub alignment for reliable operation. What it does:

• Seals the back of the washer tub to stop water from leaking at the rear
• Provides the mounting surface and alignment for the tub and rear components
• Helps prevent moisture damage to internal components and wiring
• Common symptom: water pooling or dripping from the rear of the machine

• One rear bulkhead assembly with seal

• Disconnect power and shut off water before beginning any repair
• Handle the seal carefully to avoid nicks; damaged seals can leak
• Basic hand tools required; verify fastener locations and torque per OEM guidance

This bracket is the mounting base for the dryer's cylinder support roller. Replacing a bent or worn bracket restores proper roller alignment so the drum turns smoothly, reducing vibration and noise and preventing premature wear.

• Provides the fixed mount for the cylinder support roller
• Maintains drum alignment for smooth, even rotation
• Replace if the bracket is bent, cracked, or mounting holes are elongated
• Common symptoms of a failing bracket: loud rumbling/thumping, scraping, excessive vibration, or visible roller misalignment

• Disconnect power; for gas models, also shut off gas supply
• Access the roller area per your model's service information and support the drum
• Transfer the roller/axle and spacers from the old bracket; install the new bracket in the same orientation
• Verify the roller spins freely and hand-rotate the drum to check for binding before test run

The Roller Cylinder is an OEM replacement part for Speed Queen dryers. This component supports the dryer drum and enables smooth rotation during operation, reducing friction and ensuring consistent performance. Proper functioning of the roller cylinder is essential for maintaining the balance and efficiency of the dryer drum.

Causes of a bad Roller Cylinder can include natural wear over time, exposure to heavy loads that strain the rollers, or debris accumulation that affects smooth movement. Misalignment of the drum or poor maintenance practices can also contribute to roller failure.

Symptoms of a bad Roller Cylinder include:

• A thumping or rumbling noise during operation
• The drum wobbling or not spinning smoothly
• Visible wear or damage to the roller upon inspection

This OEM Speed Queen part is also compatible with Alliance laundry equipment.

Dryers, washers, and washer dryer combos are made with an idler pulley shaft. It works in combination with the rest of the equipment in multiple ways. It switches the direction in which the output shaft is rotating. The idler pulley shaft also works to change gears and maintain the space between shafts. With time, because of excessive force, or as a result of misuse, the idler pulley shaft can wear out, break, or get damaged otherwise. When the part isn't working correctly, it has to be replaced to continue using the machine.The primary indication that there is something wrong with the idler pulley shaft is a machine that's producing excessive noises. Replacement of the idler pulley shaft is a straightforward process. It can be done in a few minutes with a nut driver and screwdrivers. Unplug the appliance before starting the disassembly.This idler pulley shaft is a genuine OEM replacement part. It is sold as an individual unit. It is made of durable metal materials. The idler pulley shaft is sourced from the manufacturer. It can be installed in various machines made by Speed Queen, Amana, and Magic Chef.

The Roller Kit is an OEM part for Speed Queen dryers manufactured from 1992 and newer. This kit includes the rollers and necessary components that support the dryer drum, ensuring smooth and stable rotation during operation. The rollers help reduce friction and wear on the drum, contributing to the overall efficiency and longevity of the dryer.

Causes of a bad roller kit can include wear and tear from regular use, accumulation of lint and debris, and mechanical damage from overloading the dryer.  

Symptoms of a bad roller kit include:

• Unusual noises such as squeaking or thumping during dryer operation
• The dryer drum not turning smoothly or becoming stuck
• Excessive vibration or shaking of the dryer
• Visible wear, cracks, or damage to the rollers

This OEM part is designed specifically for Speed Queen dryers from 1992 and newer, ensuring reliable performance and a perfect fit.