Remington Chipper Shredder Parts

This is a flexible coupling bushing - commonly called a spider bushing - that connects the engine to the hydraulic pump on a log splitter. It absorbs vibration and compensates for minor misalignment between the motor shaft and pump shaft. Replace this bushing if you notice excessive vibration, unusual noises from the pump area, or if the hydraulic pump is not engaging properly.

This is a spiral roll pin measuring 0.156 inches in diameter and 1 inch in length, used to secure rotating components on chipper shredders and lawn vacuums. It holds parts in alignment on shafts and prevents slippage during operation. Replace this pin if it is sheared, bent, or missing, which can cause loose or non-functioning attachments.

Log splitter won't engage or makes grinding noises? This jaw coupling connects drive shafts and absorbs shock loads. Moderately easy DIY repair.

Log splitter won't engage or pump shaft disconnected? This .875 coupling connects the engine shaft to the hydraulic pump for proper power transfer.

This OEM replacement push cap can be used in a variety of lawn and garden equipment. The push cap is secured to the end of a shaft, providing protection to the user from the sharp metal edge of the shaft. The push caps that are included with the machines may wear out over time or fall off in some cases, creating an injury risk involving sharp metal edges. These push caps are high-quality and made from durable plastic. They are easy to install. The OEM push cap is a genuine part made by the original manufacturer, to ensure quality and s proper fit. The push caps can be used on lawn tractors, chippers, shredders, log splitters, and other equipment. Some of the brands that this push cap is compatible with include MTD, Husky, Yard-Man, Bolens, Troy-Bilt, Ryobi, Yard Machines, and cub Cadet.

Spring roll pin fastener for lawn mowers and outdoor power equipment. Secures components in place. Replace if missing, worn, or damaged during repairs.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This air cleaner cover is designed to house the air filter on larger lawn equipment and other outdoor power tools. There is no aspect of small engine care more necessary than protecting the air that goes into the carburetor and cylinder from yard dust. Nothing is more incapacitating to a small engine than being clogged with dust, pollen, and other particulates that are invariably stirred up during landscaping work. While the air cleaner cover itself is not a moving part and would not seem to be subject to replacement, it is occasionally the case that, through extensive use or accidental contact, the cover becomes unable to shield the air filter within it. In these cases, it is essential to replace the cover with an OEM certified replacement cover that has been manufactured to the same specification as the original. Though replacing the cover itself is quite simple, it probably a very good idea to replace the air filters at the same time. If the cover is in need of replacement, it is quite likely the filters have been exposed to excessive amounts of particulate. This cover can be used on chippers, shredders, log splitter, mowers, and a variety of other small engine/large job equipment. Compatible brands include Troy-Bilt, MTD, Yard-Man, Yard Machines, and Cub Cadet.

Replacement blade for chipper shredders. Installs on the cutting mechanism to chip wood into small pieces. Replace when dull, chipped, or damaged.

This genuine OEM replacement jam nut attaches to the idler bracket on a tiller. Jam nuts are a special type of nut designed to not unthread or strip out over time. Jam nuts are usually fastened on with another standard nut and then the two nuts are tightened against each other. Jam nuts can be easily identified from a standard nut because they are roughly half the size. Jam nuts can be lost while making repairs because of their small size. If lost, it might not affect the idler bracket immediately, but over time the standard nut may begin to slip or unthread. Therefore, the jam nut should be replaced as soon as possible. When making this replacement, be sure to unthread the standard nut as well and then tighten them both together using a wrench. This replacement jam nut is a high-quality part sourced from its original manufacturer. It is compatible with Troy-Bilt, Yard Man, Huskee, MTD, Ryobi, Yard Machines, and Cub Cadet tillers. This part does not ship with any additional hardware.

Replacement washer for lawn mowers and outdoor power equipment. Installs with bolts to distribute load and prevent loosening. Replace if worn or missing.

Fuel line kit for small engines. Carries fuel through the machine. Replace if cracked, leaking, or ends don't fit securely even when clamped down.

Fuel tank nipple connects fuel lines to the tank on small engines. Replace if cracked, leaking, or worn to restore proper fuel line connections.

Fix a starter that won't pull freely or spin the flywheel fast enough. This metal-housed recoil starter assembly fits multiple MTD engine models.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

Hex cap screw secures components on lawn tractors, tillers, snowblowers, and garden equipment. Replace if broken, stripped, or missing.