Remington Edger Parts

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

This genuine OEM replacement part is an extension spring for a Craftsman snowblower idler pulley assembly. The idler pulley attaches to a part of the snowblower's housing and is helps to transfer energy throughout the belt drive. This extension spring helps to redistribute some of the back-and-forth motion created in the pulley as the snowblower runs. This keeps the assembly from shifting out of place and potentially slipping. This extension spring is attached at two points and, if pulled in both directions too far, can eventually lose some of its tension. When this happens, the idler assembly can begin to shake and even slip out of place. Replacing the extension spring is an easy job that will only require a socket wrench to remove the idler pulley. A pair of pliers may help to remove the spring from its clips. This part is only compatible with Craftsman snowblowers and is sourced from its original manufacturer. It ships individually and any additional parts needed will have to be purchased separately.

This replacement part is a hand-held oil pump, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This oil pump is small and portable and is able to assist the user during oil changes in their lawn mowers. Oil changes are a normal part of maintenance for many lawn mower models and this oil pump will facilitate that.A user might require a new oil pump if the old one is damaged. This part with the lawn mower at purchase, so it may need to be purchased after the fact. It makes changing the oil inside of the engine very easy.This hand-held oil pump is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer. This device can come in handy for those looking to change the oil in their lawn mowers.

This carriage bolt is a genuine MTD part, sold individually. This carriage bolt can be used as a replacement part in lawnmowers, snowblowers, tillers, and edgers. The purpose of the carriage bolt for one of these outdoor appliances is to work in conjunction with a nut to affix two metal components to one another or one metal component to another wood component.The carriage bolt in an outdoor appliance might have to be completely replaced if it cannot affix two or more components together. This could occur if the carriage bolt has been punctured, dented, cracked, warped, or eroded to the point that it loses its functionality. If this occurs, the carriage bolt should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This carriage bolt is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Bolens, Yard-Man, and MasterCut.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

This replacement part is a deflector flap. This is a genuine replacement part made by MTD. This part is usually found on certain types of lawn mowers. It is responsible for keeping parts of the machine safe from flying debris and other things that might cause harm to the appliance. A new deflector flap might be needed if the current one has been misplaced or is damaged and no longer in working condition. If the flap is torn or ripped in any way, it might be at risk for allowing debris to enter into the lawn mower. This can cause damage inside the machine and should be replaced if this is the case. This should be a fairly simple repair. This deflector flap part is a genuine OEM replacement part to ensure proper fit and long-lasting use. This part is sold individually and is sourced directly from the manufacturer.

The hex lock nut is found on many different types of outdoor lawn equipment, as well as other types of equipment. The lock nut works to secure bolted joints by adding friction to the bolt threads. The nut has flat sides, which can easily be gripped by a wrench to be tightened or loosened as needed. These types of nuts are common, as they provide easy assembly and disassembly of various parts. Buyers may need a new hex lock nut for a range of reasons. The nut that is currently on the equipment could have become damaged or lost while working on the machine. It is vital for all of the nuts to be in place and properly secured on the equipment before use. This is an authentic OEM part. Some of the products that use hex lock nuts include lawn mowers, snowblowers, tillers, edgers, string trimmers, and log splitters. Common equipment brands using these nuts include Craftsman, Toro, Cub Cadet, Yard Machines, and Troy-Bilt.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This is a genuine carburetor insulator gasket that is designed to fit select models of lawn mowers. The carburetor insulator gasket is responsible for insulating the carburetor to create a strong seal between it and the engine block and insulate it from the excess heat. This gasket is subject to constant pressure and extreme heat, which can cause it to compress, warp, or become otherwise damaged as a result of regular use. Gaskets should be on the routine maintenance schedule and should be inspected every time other repairs are performed. Without functional gaskets, the engine may run poorly or may not run at all. This genuine OEM carburetor gasket is manufactured by MTD. It can be used in select machines from this brand, as well as those from Troy-Bilt, Cub Cadet, HUSKEE, Yard Man, and Yard Machines. There are hundreds of compatible units that take this gasket. The gasket is made of durable composite materials and sold as an individual unit. Hardware and additional components will require another purchase. Be sure to allow the engine to cool and use the appropriate tools for proper installation without damaging the gasket. Always drain the fuel system before working on the carburetor or internal engine components.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

This is a starter recoil assembly. It is used when starting small lawn equipment and other machines. It engages the flywheel. With time and use, any or all of the recoil can wear out or become damaged, including the spring, housing, rope, or pulley. If something is damaged or worn out, the entire starter recoil assembly must be replaced. Signs that the part requires a repair include an engine that won't start or has difficulty engaging.Replacing a starter recoil assembly is easy and can be done in about 15 minutes. A nut driver and screwdriver are required for the repair. Wear gloves. Make sure the equipment is completely cooled before beginning the recoil assembly replacement. After putting tension on the spring and pulley, hold the housing securely to prevent it from releasing.The starter recoil assembly is a genuine OEM-authorized replacement part. It is sold individually. The starter recoil assembly is compatible with MTD, Cub Cadet, Yard Machines, Husky, Yard-Man, and Troy-Bilt brands. It is a complete part that includes the housing, rope, pulley, and recoil spring. It works with small engines, lawnmowers, log splitters, trimmers, and other similar equipment.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This is a genuine OEM idler arm bracket sourced directly from the manufacturer; it is used on various lawnmowers and garden tractors to support the idler arm, which applies tension to the blade drive belt and allows the belt to turn. If the idler arm bracket bends or breaks, the idler arm will not stay in place and the blades will not turn. The idler arm is essential to the mower being able to do its job and cut the lawn. The idler arm support brackets can be damaged by debris and stationary objects encountered while in operation.A wrench set is needed to remove and reinstall the idler arm support bracket. Before starting, remove the fuel from the gas tank and take the spark plug out. The idler arm support bracket is located under the idler arm and is found on the deck of the mower. Detach the deck from the lawnmower to access the idler arm support bracket. Remove the damaged support bracket and install the new one with the screws from the original bracket. Reinstall the mower deck, spark plug, and fuel.This idler arm bracket is made of heavy-duty metal and sold as an individual unit. It is compatible with push lawn mowers and riding lawn mowers manufactured by Yard-Man, Troy-Bilt, MTD, and Cub Cadet.