Remington Snow Removal Equipment Control Cable

This replacement part is a clutch auger cable. It connects the handle controls to the equipment's motor, which allows the user to control the speed and power of the snowblower.Over time, the auger cable's wires could snap, necessitating replacement.This is a genuine OEM replacement part manufactured by MTD for use in snowblowers and snow throwers. This part is sold individually.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This part is a speed select cable. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or detached speed select cable on certain snowblower models. The speed select cable works by fastening the ground drive system to the speed control level. This enables the equipment operator to properly control speed and traction while using a snowblower. Over time, speed select cables can experience wear and tear which can cause them to break or become detached, requiring replacement. Without a functioning speed select cable, the snow blower will not be able to be properly controlled. For accurate information on how and where to install this replacement speed select cable, specific manufacturer diagrams should be referenced. Proper safety measures should always be followed when working on any type of equipment.As an authentic replacement part, this speed select cable can be used on multiple different models of Craftsman, MTD, Yard-Man, and Huskee snow blowers. Please note that this speed select cable is a genuine part made of high-quality materials and is sold individually.

This drive cable is made up of a metal cable housed by a flexible plastic casing. It connects the drive control in the handle of the snowblower engine. This ensures the equipment starts and stops when a person wants it to. If the cable is damaged or broken, the snowblower will not work properly even when the control handle has been released.If the equipment isn't stopping or doesn't start when it should, the drive cable could be causing the problem. It will need to be replaced for the snowblower to work properly. Before making the replacement, the spark plug wire should be removed. Next, release the cables in the handle. The drive cover should be removed before taking out the drive cable. Replace this with a new drive cable and reassemble the snowblower before using it.This is a genuine OEM replacement drive cable that is sourced directly from the manufacturer. It is sold as an individual part. These cables are made to fit snowblowers created by MTD, Craftsman, and Yard Machines.

This is a drive cable that is used in many models of snowblowers from top manufacturers. It is composed of a metal cable that is inserted into a flexible plastic housing. The purpose of the drive cable is to connect the drive control located in the snowblower engine handle. It makes sure that the snowblower starts and stops when the controls are used. If the drive cable is broken or becomes damaged, the snowblower will not work correctly even if the control handle is released.If a snowblower isn't starting or stopping when expected, the drive cable is likely the source of the problem. The part needs to be replaced before the snowblower can be used again. Disconnect the spark plug wire before releasing the handle cables and removing the drive cover. Replace the drive cable and reassemble the other parts.This is an authentic OEM replacement drive cable that is sourced directly from the manufacturer. It is sold as an individual component. The drive cable is designed to be compatible with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.