Remington Control Cable

This throttle cable is a used on string trimmers. This part links the carburetor assembly to the throttle trigger. Each throttle cable is made with a connector on each end. Over time, the throttle cable can be damaged or kinked through use. If this occurs, the cable will need to be replaced.Replacing the throttle cable will require basic tools and a set of work gloves. The first step to replacing the throttle cable is removing the original component. The throttle housing will need to be taken apart on each side of the string trimmer. The replacement cable will pass through the carburetor mounting plate hole and the engine housing before reassembling the rest of the parts.This throttle cable is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The throttle cable is made for use with string trimmers manufactured by Yard Machines, MTD, Craftsman, Murray, Yard-Man, Bolens, and Cub Cadet.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This part is a speed select cable. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or detached speed select cable on certain snowblower models. The speed select cable works by fastening the ground drive system to the speed control level. This enables the equipment operator to properly control speed and traction while using a snowblower. Over time, speed select cables can experience wear and tear which can cause them to break or become detached, requiring replacement. Without a functioning speed select cable, the snow blower will not be able to be properly controlled. For accurate information on how and where to install this replacement speed select cable, specific manufacturer diagrams should be referenced. Proper safety measures should always be followed when working on any type of equipment.As an authentic replacement part, this speed select cable can be used on multiple different models of Craftsman, MTD, Yard-Man, and Huskee snow blowers. Please note that this speed select cable is a genuine part made of high-quality materials and is sold individually.

This drive cable is made up of a metal cable housed by a flexible plastic casing. It connects the drive control in the handle of the snowblower engine. This ensures the equipment starts and stops when a person wants it to. If the cable is damaged or broken, the snowblower will not work properly even when the control handle has been released.If the equipment isn't stopping or doesn't start when it should, the drive cable could be causing the problem. It will need to be replaced for the snowblower to work properly. Before making the replacement, the spark plug wire should be removed. Next, release the cables in the handle. The drive cover should be removed before taking out the drive cable. Replace this with a new drive cable and reassemble the snowblower before using it.This is a genuine OEM replacement drive cable that is sourced directly from the manufacturer. It is sold as an individual part. These cables are made to fit snowblowers created by MTD, Craftsman, and Yard Machines.

This replacement part is a clutch auger cable. It connects the handle controls to the equipment's motor, which allows the user to control the speed and power of the snowblower.Over time, the auger cable's wires could snap, necessitating replacement.This is a genuine OEM replacement part manufactured by MTD for use in snowblowers and snow throwers. This part is sold individually.

This is a drive cable that is used in many models of snowblowers from top manufacturers. It is composed of a metal cable that is inserted into a flexible plastic housing. The purpose of the drive cable is to connect the drive control located in the snowblower engine handle. It makes sure that the snowblower starts and stops when the controls are used. If the drive cable is broken or becomes damaged, the snowblower will not work correctly even if the control handle is released.If a snowblower isn't starting or stopping when expected, the drive cable is likely the source of the problem. The part needs to be replaced before the snowblower can be used again. Disconnect the spark plug wire before releasing the handle cables and removing the drive cover. Replace the drive cable and reassemble the other parts.This is an authentic OEM replacement drive cable that is sourced directly from the manufacturer. It is sold as an individual component. The drive cable is designed to be compatible with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.

This control cable is a mower part that works with the control handle or lever bar that engages the wheels. It is also known as choke cable, brake cable, choke control, and control assembly cable. The inner wire total length is 53 inches, and the cable casing or conduit length is 40 inches. The control cable can stretch over time and it will result in a mower that moves forward slower than usual. A cable that's too corroded won't be capable of moving the drive lever. A broken or cut cable won't make the mower move. Here is a manufacturer-approved replacement control cable that's easy to install. A genuine OEM replacement part, this control cable is made to fit specific models of walk-behind mowers from Bolens, Ryobi, MTD, Troy-Bilt, and Yard-Man. It is sold individually.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This control cable is a genuine MTD part, sold individually. This control cable can be used as a replacement part in a string trimmer. The purpose of the control cable in a string trimmer is to allow the operator of the appliance to propel the appliance forward or stop the appliance by engaging or disengaging the cable.The control cable could be frayed, dented, warped, ripped, torn, or eroded, and if this occurs to the point at which the control cable cannot control the motion of the appliance, the control cable should be removed and replaced by this genuine OEM replacement part for continued safe use of the string trimmer. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This control cable is compatible with the following outdoor appliance brands: MTD and Cub Cadet.