Parts for Briggs & Stratton 219800 (0113-0421): Motor Starter / Rewind Starter Parts

This oil seal is a genuine OEM replacement part designed for use on a wide variety of small gas-powered appliance engines. Although small, an oil seal is an important part of the oil cylinder assembly as it prevents oil from leaking into other parts of the engine. If oil begins to leak into the engine, it can corrode other parts or even pose a fire hazard. Therefore, it's important that the oil cylinder is tightly sealed to prevent any damage to the engine. Seals can wear out over time, especially if exposed to heat. Heat will cause the seal to shrink, effectively unsealing the oil cylinder. Before making this repair, be sure to drain the oil cylinder of any oil and be prepared for an involved replacement process. This part is compatible with Toro, Murray, and Briggs & Stratton appliances and is sourced from the original manufacturer. It ship individually of other hardware.

This is a genuine replacement cylinder head gasket designed for use on select engines from Briggs & Stratton. This gasket is located on the cylinder head. It helps seal the engine and absorbs fuel leaking and preventing damage to other engine parts. Over time, it can shrink or become saturated due to constant exposure to high heat, vibrations, fuel, and pressure. A bad cylinder head gasket can affect engine performance and impact a variety of other systems or even keep the engine from operating at all until it is replaced. This OEM part can provide an exact fit for compatible models.This genuine cylinder head gasket is a replacement that can be used on engines found in tractors made by Toro and Briggs and Stratton. This is a cardboard composite gasket and will require a screwdriver to replace. This part is sold as a single unit. Engines should be completely cool before beginning repairs and users should always wear gloves to protect their hands.

The crankcase is a metal case over the crankshaft of an engine. It is essential to the operation of the engine as it shields the crankshaft and rods from any debris. It also ensures the pressurization of the chamber and helps to keep pistons and oil moving properly. The crankshaft gasket is part of what keeps the seal and allows the engine to function. It can wear with time or even become dry and cracked. It will cause oil leakage, smoke, and even engine failure. This is a genuine OEM crankcase gasket for lawnmowers, lawn tractors, and small engines produced by Toro, Cub Cadet, MTD, Briggs & Stratton, and Simplicity. It comes as an individual component.

This screw is a genuine Midwest Engine part, sold individually. This screw can be used as a replacement part for a variety of small engine outdoor appliances including lawn mowers, snowblowers, and wood chippers. The purpose of a screw in such outdoor appliances is to provide a secure fastening for two or more components to one another through the piercing of the screw into the components and the rotation of the screw so that its placement is stable.The screw of a small engine outdoor appliance is a small component that can be easily lost or misplaced. If the screw is stripped or otherwise damaged, it should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Toro, Craftsman, Cub Cadet, Murray, Lawn Boy, MTD, and Simplicity.

This replacement oil drain plug is a genuine OEM part for a lawn tractor or generator engine. The oil drain plug connects to the base of the oil tank and allows the appliance owner to drain used oil and replace it with new, clean oil. The oil drain plug is threaded to screw into the oil tank and prevent it from popping out of place while the appliance is in use. The most likely reason to replace an oil drain plug is if the old plug's threading has become stripped and no longer holds onto the oil tank. Alternatively, the plug is quite small and could easily be misplaced during an oil change. If lost, oil will leak from the engine, causing parts to overheat. Fortunately, replacing a lost or damaged oil drain plug is simple and only requires screwing a new plug into place. This replacement plug is a high-quality part that fits Craftsman and Murray products. It comes sourced from its original manufacturer and ships individually, without any additional hardware.

The flywheel key is the component on outdoor equipment that keeps the flywheel connected to the crankshaft. Over time, this key may become damaged or broken, particularly if the engine experiences a forceful stop, like hitting a large stationary object. If the flywheel key breaks, the engine will not start. A slightly damaged flywheel key is noticeable through symptoms like misfiring, backfiring, or having no power. If any of these are occurring, the flywheel key should be replaced to prevent complete engine failure.A flywheel puller tool is required for this repair. Make sure the engine is cool before working on the flywheel. Wear safety gear, including gloves and eye protection. Disconnect the spark plug and remove the blower housing. Remove the flywheel mounting nut and set it aside. Take the recoil starter cup off the mower. Use the flywheel puller to remove the flywheel and access the flywheel key. Remove the broken flywheel and replace it with the new flywheel. Reverse the steps to put the mower back together.This flywheel key is made of an aluminum alloy and is sold as an individual part. It is designed for use in lawnmowers, lawn tractors, and other small engines manufactured by Briggs and Stratton, Toro, Lawn-Boy, Simplicity, MTD, and others.

A keeper valve is a small piece of hardware used to help to secure a valve. It is designed for use with pieces of outdoor lawn and garden power equipment that have small engines, a lawn mower, a snowblower, and a wood chipper. It is compatible with products by brands such as Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn Boy, MTD, and Simplicity.The keeper valve fits into a groove in the end of the valve stem to secure the valve spring, valve spring retaining washer, and valve stem together. It is only natural that, over time, the keeper valve may wear out from regular exposure to the elements, get damaged, fall out, or become lost. In any of these events, a replacement will become necessary.The replacement or repair process of the keeper valve should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location. This keeper valve is an original OEM part sourced directly from the manufacturer, Midwest Engine. It is sold individually.

This genuine OEM replacement intake manifold gasket for a small gas-powered lawn appliance motor acts as a seal between two engine components, like any other gasket. However, the intake manifold gasket is one of the most necessary gaskets because it is responsible for sealing the engine vacuum and coolant. Intake manifold gaskets can be damaged because of their location in the engine. If the engine has been running hot for a while, the metal can expand and crush the gasket, causing it to fail. If this happens, the engine will begin overheating, as coolant can no longer reach the areas where it is needed. Replacing an intake manifold gasket will mean removing the air filter and its housing, the oil drain tube, blower housing, breather tube, and carburetor. Making this repair requires a set of socket wrenches and screwdrivers. This part is compatible with a wide range of mowers, chippers, and blowers from Briggs & Stratton, Toro, Cub Cadet, MTD, Simplicity, and Lawn Boy. It is sourced from the original manufacturer and ships individually.

This replacement part is an idle speed kit. This is a genuine replacement part made by Midwest Engine. This part is responsible for preventing the engine of many types of machines from stalling during idle time. A new idle speed kit might be needed if the engine stalls out when it is not in motion. This can be due to a faulty idle speed kit and should be replaced. It is important that before attempting to replace this part, the engine is completely off. This can affect the installation and cause damage to the engine. Be sure to wear work gloves when working near the engine of any machine. This part is a genuine OEM replacement part for long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This is a genuine float needle valve that is designed to be used in select small engines found in lawn tractors. The float needle is located in the carburetor and is responsible for assisting with the intake and outflow of gas through the assembly. As the fuel bowl in the carburetor fills and drains, this needle regulates how much fuel is present to ensure the proper operation of the engine. Over time, the valve can become cracked or get damaged because of repetitive motion and exposure to high heat. This could impact the flow of fuel and the engine performance, or cause the engine to fail completely. This genuine OEM float needle valve is manufactured to exact standards as an identical replacement for select Briggs & Stratton small engines found in lawn tractors. It can also be used with certain models from Toro and Vanguard. It is sold as an individual unit and made of durable plastic. Be sure to drain the fuel from the engine and allow it to cool before doing any repairs. Gloves are also recommended for safety. For those who need additional components, this valve may also be available as part of a compatible carburetor rebuild kit.

This is a carburetor float that is used in a wide variety of lawn and garden equipment. The carburetor float is used in the engine to close and open the float needle valve. The main responsibility of the carburetor float is to open up to allow fuel into the carburetor when drained and to shut off the flow of fuel if the bowl is filled. If the float isn't working properly, the engine may not idle, the carburetor can flood, and the motor may stall while the tool is in use.Before replacing the carburetor float, put on work gloves and disconnect the spark plug wire. The carburetor will need to be removed from the equipment. The carburetor float and any other malfunctioning parts can be taken out and replaced with new components. While working on the parts, the jets can also be cleaned as a maintenance process.This carburetor float is sold as an individual item. It is an authentic OEM replacement part sourced directly from the manufacturer. The float is designed to be used with lawnmowers, lawn tractors, wood chippers, and snowblowers manufactured by Cub Cadet, Briggs & Stratton, MTD, Toro, and Simplicity.

When the fuel in a small, gasoline-powered engine moves up the fuel line, it must be mixed perfectly with air and together burn in just the right mixture and amount in order for engines to function properly. Because too much gas might be coming into the carburetor or because there might be a need for more gasoline than can readily move up the fuel line, the carburetor has a small device called the float bowl. The float bowl has a ready supply of gasoline for use as needed by the carburetor. To keep the gasoline in check while all this is happening, a device called the float bowl gasket keeps all the elements separate. With use and age, sometimes these gaskets crack or grow brittle and must be replaced. This causes air to leak into the mix and the engine will not operate smoothly. Replace this gasket with a genuine OEM replacement part like this one, manufactured to be exactly like the factory original that is being replaced. This part is compatible with engines sold by Toro, Simplicity, MTD, Briggs & Stratton, and Cub Cadet. Part sold individually.

This float bowl gasket is a replacement part for use with lawn and garden equipment, as well as other small engines. The section of the carburetor that is shaped like a bowl where the fuel reserve is maintained is regulated by a float. The float bowl gasket helps to ensure that there are no leaks in this area. The float bowl gasket may start to wear down in time, and it will need to be replaced to prevent fuel leaks. If there are leaks present, it could be due to an issue with this gasket, so it should be checked and replaced if needed. When replacing the gasket, it is important that the surfaces are clean and dry. It is also important that no solvents or gasket sealers are used with this gasket. The genuine OEM float bowl gasket is sold individually and will work to replace the gaskets in lawn tractors, lawn mowers, and other small engines. The compatible brands include Craftsman, Toro, Wheel Horse, Lawn-Boy, Simplicity, and Briggs & Stratton.

This fuel line is a genuine OEM replacement for select Briggs & Stratton engines. The fuel line is responsible for delivering fuel to the carburetor from the fuel tank. Over time and with regular use, the fuel line can become brittle or worn, causing cracks or breaks that require a replacement. If a leak is noticed or if the machine seems to be using too much fuel, there may be an issue with the line. This fuel line replacement provides an exact fit for compatible engines. This fuel line is manufactured to exact standards and designed to fit various lawn and garden equipment engines, including pressure washers, generators, snowblowers, and lawn tractors. There are more than 150 machines with compatible engines for this fuel line, including those from Briggs & Stratton, Toro, Murray, Snapper, Troy-Bilt, Husqvarna, Simplicity, and Vanguard. It is cut to fit for an exact fit and includes a ¼-inch diameter on the interior and a ½-inch diameter on the exterior. The fuel line also comes with replacement clips. It is sold as an individual part and made of durable, high-quality rubber with coated metal clips for a secure fit.

This replacement part is a fuel line. This is a genuine replacement part made by Midwest Engine. This part is commonly found connected to fuel tanks and is able to provide the proper stunned for the fuel to travel through when needed. A new fuel line might be needed if the current one is no longer able to stay connected to the machine, if the current line is leaking in any way, or if the line has become damaged. This can be due to normal wear and tear over time and should be replaced if this is the case. Work gloves are recommended when working with parts that have touched fuel. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This is a fuel line replacement intended to keep a lawnmower's engine running smoothly. It is long enough to make a couple of fuel lines, just cut the fuel line to the desired length and keep the rest as a spare. When a mower doesn't start easily or performs poorly when running, the fuel delivery system may have a problem and will need repair. The fuel line that supplies gas from the tank to the carburetor may be cracked or broken. When this occurs, it is best to replace the fuel line before it becomes a flammable hazard. This is an OEM replacement fuel line sourced from the manufacturer and is sold individually. This replacement part is compatible with different Briggs & Stratton mowers. Remember to use work gloves and drain the gas tank before the installation of this part.

This is a replacement rocker arm adjuster that is specifically designed for use in select lawn mower engines. The rocker arm adjuster attaches to the rocker arm, which is responsible for opening and closing the valves on the engine responsible for injecting fuel and air. By doing this, it impacts the horsepower and performance of the engine. Over time, rocker arm adjusters can become lost or damaged. If they are not functional or are missing, the rocker arm will not be able to open and close the valves appropriately and the engine may not function at all. This genuine OEM rocker arm adjuster is manufactured to exact standards for Briggs & Stratton engines and is designed to offer an exact replacement for the part that came with the machine originally. This part can also be used as a replacement on select models from Toro and Lawn Boy, with over 150 machines that can use this rocker arm adjuster in total. The part is made of durable materials and sold as an individual unit. No additional hardware or parts are included. Never perform repairs on a hot engine and always wear gloves for hand safety.

This genuine Midwest Engine valve cap protects the internal workings of the small engine by keeping dirt, debris, pebbles, and any other small material picked up by the appliance out of the engine. The valve cap of a small engine outdoor appliance might have to be replaced if it suffers damage or if it is simply lost or misplaced, which could allow dirt and debris swept up into the air by the appliance to enter the infrastructure of the machinery and cause internal damage. Before more severe damage occurs, it is best to remove and replace the damaged valve cap. This replacement should be done before using the outdoor appliance again, as to not run the risk of further damage. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This valve cap is compatible with the following brands: Midwest Engine, Briggs & Stratton, Toro, Simplicity, Lawn-Boy, MTD, Craftsman, and Cub Cadet. It can be used as a replacement part for the small engines of outdoor appliances such as lawn tractors, lawn tractors, snowblowers, wood chippers, leaf blowers, tillers, and edgers. This part is sold individually.

This is an inline fuel filter and is an essential part of a fuel system. This part can be found inside the fuel tank or fitted into the fuel line. The fuel filter is responsible for straining particles like water and debris in the fuel so that they won't reach and clog the combustion chamber and eventually reduce the engine's performance. Annoying sputters when starting equipment and uneven idling are incidents that may be related to a clogged fuel filter. To remove a fuel filter, first cut off the fuel supply and then slide the fuel clamps away to remove the filter. Remember to work in a well-ventilated area, with no open flame or fire source, when installing this component. This part works with lawn mowers, snowblowers, tillers, generators, wood chippers, and others with small engines. It is compatible with brands such as Briggs & Stratton, Craftsman, Toro, Cub Cadet, Murray, Lawn Boy, Snapper, and Simplicity. This is a manufacturer-supplied OEM replacement part and comes as an individual component.

The washer seal is an essential part of the carburetor float bowl on engines with carburetors on lawn mowers. This washer prevents gasoline leaks from the carburetor by sealing the bolt to the bowl.The washer seal is normally replaced when overhauling the carburetor. Reusing the old one is not recommended. If the seal between the bolt and the bowl is not tight, gasoline could leak and cause damage to the engine or cause bodily injury due to combustion. There are normally two bolts on the carburetor bowl. Each bolt will have a washer seal. It is a good idea to replace both seals at the same time to ensure both are flush with the bowl.When replacing the washer seal, it has to be flush and tight but not overtightened. If it is overtightened, it can crack and strip, making it leak and useless. If necessary, the washer can be trimmed to make a tighter fit. After making sure the fit is flush, it slides over the bolts that make the connection from the bolt to the bowl. The bolts are then tightened.This OEM Midwest Engine washer seal is sold individually for Briggs and Stratton lawn mower and lawn tractor engines.

This is a screw that is used in many types of lawn and garden equipment, including lawnmowers and wood chippers. It comes with a black finish and is made of durable metal. The screw can be used in many locations on a tool to attach two components together. Screws can also be used in tandem with nuts, but the two components should have the same threading and finish.Screws can become damaged, break, or be stripped and will need to be replaced. Corrosion, extreme temperatures, and unexpected stress can all lead to issues with a screw. A visual inspection can indicate whether the screw should be replaced. If it does need replacement, a screwdriver can be used to remove the original screw. The new component can be placed and tightened.This screw is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as a single component. The screw can be used with many types of lawn and garden equipment, including lawnmowers, tillers, pressure washers, leaf blowers, edgers, generators, wood chippers, and snowblowers manufactured by Briggs & Stratton, Cub Cadet, Craftsman, Murray, Wheel Horse, Lawn-Boy, MTD, MasterCut, Simplicity, and Toro.

The stop wire is a safety cable device offered on many types of lawn and garden equipment. It is pressed near the upper handle of a device to start it, which lets the blades spin and creates forward motion on equipment that is self-propelled. A stop wire can stretch out over time and will need to be replaced to ensure total safety. If the blade brake control is released and the blades continue to spin for more than a couple of seconds, the wire needs to be replaced.Take the equipment and put it on a flat surface before taking the metal on the stop cable and moving it out of the mower handle. Squeeze the center tabs of the wire with needle-nose pliers and pull the cable end through the bracket. Pull the other end out and then replace it with a new component.This is an authentic OEM replacement part for use with garden equipment engines. It is an individual part that is sourced directly from the manufacturer. This part is compatible with lawnmowers, wood chippers, snowblowers, generators, log splitters, tillers leaf blowers, and pressure washers by Briggs & Stratton, MasterCut, Craftsman, Simplicity, Toro, MTD, Cub Cadet, Lawn-Boy, Murray, and Wheel Horse.

This is a replacement screw to secure the pawl friction plate used in many types of lawn and garden equipment. The part is also sometimes called a flange bolt. It is identical to the original screw that came with the machine and will replace a lost or damaged screw. The screws could become damaged due to corrosion or an incident that causes the screw to bend or break. They also serve as replacements in case the screw was lost. Replacing the screw is a simple repair to make. This is an authentic OEM replacement screw that is sold individually. Some buyers might want to have an extra screw on hand. The replacement screw for the pawl friction plate can be used on lawn mowers, snowblowers, tillers, pressure washers, generators, edgers, log splitters, wood chippers, and other small engines. Compatible brands include Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn-Boy, Snapper, MTD, and Simplicity.

This is an O-ring seal that can be used in many types of engines for lawn and garden equipment. It is responsible for sealing the connection between the cylinder head assembly and the intake manifold. The sealing process prevents dirt and debris from moving throughout the equipment and getting into the motor. As time passes, the O-ring seal can shrink, causing oil or air leaks and decreasing engine performance.When the O-ring is damaged, clogged, worn, or broken, it will need to be cleaned or replaced before using the lawn equipment again. The damaged or broken O-ring seal can be removed using a flat head screwdriver. After it has been removed, the replacement component can be installed in the same place. Make sure that the O-ring seal is properly seated to avoid additional leaks. Reassemble the parts before using the tool. This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold individually. It is used in lawnmowers, lawn tractors, snowblowers, and wood chippers manufactured by Simplicity, MTD, Lawn-Boy, Cub Cadet, Toro, and Briggs & Stratton.

The stop switch, sometimes called a kill switch, is triggered to stop the engine when the operator is no longer on the seat ,This is important for safety. If the stop switch is not functioning properly, inspect it for damage and replace it right away. Operating a machine without a functional stop switch can be dangerous. The stop switch is a genuine OEM part, and it is sold individually. The switch can work for many types of equipment including lawn tractors, lawnmowers, log splitters, wood chippers, pressure washers, and tillers. The replacement part is compatible with a range of brands, including Midwest Engine, Toro, Craftsman, Briggs & Stratton, Lawn-Boy, Murray, Snapper, and MTD.

This replacement spark plug boot is used with a range of lawn and garden machine engines. The spark plug boot is also called a coil boot and an ignition boot. It creates voltage and mounts on top of each spark plug. It connects the spark plug to the ignition coil. Over time, the spark plug boot could start to wear down. This could be due to normal wear and tear or because of an issue of a faulty boot. Regardless, it will need to be replaced. If it is not working properly, it will be difficult or even impossible to start the engine. This is a genuine OEM replacement spark plug boot that is sold individually. The boot can be used with many models of Lawn Mower, wood chipper, snowblower, and other small engines. Compatible brands include Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn-Boy, MTD, and Simplicity. Buyers should always ensure they are choosing the correct spark plug boot for their make and model.

This replacement part is a nut. This part is small but important in various types of equipment. Nuts are able to work with other small parts such as washers and screws to secure equipment components in place.If a nut has become stripped or worn down over time, it is possible that it can no longer perform the function needed. Be sure to wear work gloves when working with small parts such as nuts to prevent injury during the repair. This is a genuine OEM replacement part manufactured by Midwest Engine. This part is sold individually.

This screw is designed to be used on all sorts of lawn and garden equipment. The metal screw is durable and attaches to the muff guard bracket to keep it in place and stable while the equipment is being used. This screw can become damaged through overuse or wear and tear. It can also break or become stripped, which will require it to be replaced.Visually inspecting the area with the muff guard bracket is connected to the rest of the equipment will give information about whether the screw is broken or damaged. The screws can also be cleaned to be more visible so small problems are easier to pick up on. Sometimes the screws can become loose, which is another situation where a replacement is needed. Simply use a screwdriver to take out the old screw and replace it with a new one.This screw is a genuine OEM replacement part that is directly sourced from the manufacturer. It comes as an individual part. The screw can be used on snowblowers, lawnmowers, lawn tractors, tillers, pressure washers, leaf blowers, edgers, generators, wood chippers, and log splitters made by MasterCut, Simplicity, MTD, Snapper, Lawn-Boy, Wheel Horse, Cub Cadet, Toro, Craftsman, and Briggs & Stratton.

This replacement friction spring is a genuine OEM part meant for any number of small appliance engines run using a starter rope. This spring absorbs large amounts of kinetic energy that could damage the starter rope pulley system. It helps keep the pulley from being overstretched, which would create enough pressure to break the entire system. This spring sits at the center of the pulley system and creates resistance as the user yanks the starter rope. Friction springs can become worn out after repeated use, especially if a user tends to yank the starter rope quite forcefully. The most obvious sign of a worn of friction spring is if the pulley system lacks any resistance. As the user pulls the cord, they should feel a little pull back, but if the friction spring is worn, there will be much less resistance. Replacing this part is straightforward and will only require a screwdriver. Simply open the pulley system, carefully remove the old spring, and install the new one. This part is compatible with a wide number of appliances from Toro, Vanguard, Briggs & Stratton, and Lawnboy. It comes sourced from the original manufacturer and ships individually.

This replacement valve seal is a genuine OEM part for a lawn tractor or mower. The valve stem is a type of valve that transfers oil into the cylinder and then immediately reseals due to the pressure in the chamber. However, if the seal is damaged, it will not close and oil will leak into the cylinder. If this happens, the cylinder head may become overly lubricated and not run well. This seal helps prevent that from happening. It fastens to the intake valve and valve stem keeper. Seals will naturally wear out over time due to stress and exposure to corrosive oxidizing agents in an engine. When this happens, the valve will leak oil. To test if the valve seal is compromised, look for whitish-grey smoke that indicates burning oil and also measure to see how much oil the engine is consuming. If the seal is breached, use a screwdriver and socket wrench set to change out the part. This top of the line replacement valve seal is compatible with Briggs & Stratton, Toro, and Lawn Boy lawn tractors. It is sourced from the original manufacturer and ships individually.

Flange screws have a flange located near the top of the screw, which helps to distribute the connection force over a larger area to reduce potential damage to the machine. It also allows the screws to be used in oversized or irregular holes, and it helps to ensure they stay in place. This flange screw also has a hex top. Screws can last for a long time. However, they may become corroded or worn over time and need to be replaced. They could also become lost and need a replacement. Without all of the screws in the proper places in a machine, it could vibrate too much, which could render it less effective or unsafe to use. The flange screw is a genuine OEM part that can be used with many types of machines including lawn mowers, snowblowers, tillers, pressure washers, leaf blowers, generators, wood chippers, and other small engines. The screws are compatible with Briggs & Stratton, Craftsman, Toro, Cub Cadet, Murray, Lawn-Boy, Snapper, Simplicity, and MTD.

This gasket-rocker cover, also called a valve cover gasket, is used in small engines to create an air-tight seal between the engine and the valve cover. This cover is also made to prevent oil from leaking as it travels throughout the engine. It’s an important component to ensure the cylinder head is protected from the elements and oil doesn’t leave the motor. If this component has failed, replacement is essential to avoid engine failure. Gasket-rocker covers are protected on the bottom and top, but they may experience damage from the sides. Over time, the gasket can crack after becoming brittle, which allows dirt, heat, and debris exposure. This can lead to the cover breaking down and leaking, which may cause reduced engine performance and cosmetic problems. Some signs that replacement is needed include a burning oil smell, a dirty cover, and an engine that runs low on oil. This gasket-rocker cover is a genuine OEM component that is directly from the manufacturer. It’s designed for use with Briggs & Stratton and Toro lawn tractors and small engines. It’s sold individually and can be attached using a torque wrench or a socket set.

This rocker arm is a genuine Midwest Engine part. A rocker arm is a vital part of an internal combustion engine that controls the intake and exhaust valves in order to direct power from the engine to the wheels, setting the appliance, such as a lawn tractor, wood-chipper, snowblower, or lawn mower in motion. Natural wear and tear from extended use over a long period of time can cause an internal combustion engine to malfunction or fall into disrepair. The longer a rocker arm is in use without replacement, the more likely it is to be subject to damage. This will require a replacement rocker arm. Signs of weakening infrastructure for which the rocker arm might be responsible can include unexplained clicking noises, stalling engines, lit-up check engine lights, and clear visual signs of deterioration on or around the rocker arm itself. Always wear gloves when handling, repairing, and operating outdoor equipment.This rocker arm replacement part works with engines, lawn tractors, wood chippers, snowblowers, and lawn mowers from brands Briggs and Stratton, Toro, Cub Cadet, Lawn Boy, Craftsman, MTD, and Simplicity.

This push rod guide is designed for use with various lawn and garden equipment motors. It has a construction of plastic and metal that fits into the cylinder head assembly. The purpose of the push rod guide is to secure the push rods and keep them in the proper position. Sometimes these guides can break, become weak, or be covered in residue and need to be replaced.If there are issues with the push rod guide, remove the spark plug before removing the air cleaner assembly, oil fill tube, fuel tank, and blower housing. Any other parts in the way like muffler guards, rewind starters, and carburetors should also be removed. Take the screws off the valve cover and remove them before pressing the spring retainer and spring over a valve. At this point, remove the push rod guide and replace it.This pushrod guide is a genuine OEM replacement part sourced directly from the manufacturer. It comes as a single part. The guide is compatible with lawnmowers, wood chippers, and snowblowers manufactured by Simplicity, Briggs & Stratton, MTD, Craftsman, Lawn-Boy, Toro, and Cub Cadet. A wrench and socket set are useful for making the replacement.

This brush retainer is part of the starter motor on many types of lawn and garden machinery. It comes with both the retainer and a set of four brushes. The main job of the brush retainer is to hold a set of carbon brushes against the commutator bars located on the armature. If the brush retainer is worn, damaged, or improperly seated, it can cause problems with the equipment. The starter motor will not be able to get the proper amount of current from the battery.If the brush retainer might be causing problems, a visual inspection can be performed. A damaged brush retainer can wear down to the wire lead and become burned, pitted, or cracked. When the brush retainer is worn out, it can decrease engine performance, reduce braking, and cause the motor to lose power. This brush retainer is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual part. The retainer is made to be used with lawnmowers, snowblowers, tillers, and wood chippers created by Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn-Boy, Snapper, MTD, and Simplicity.

The Door Switch Lever is an OEM part for Whirlpool dryers. It plays a vital role in ensuring the dryer only operates when the door is securely closed by engaging with the door switch to signal the door's status.

Causes of a bad door switch lever can include normal wear and tear from repeated use, physical damage from accidental impact, or deformation from heat and humidity inside the dryer. A faulty lever can prevent the dryer from starting or stopping correctly.

Symptoms of a bad door switch lever include:

• Dryer not starting
• Dryer stopping mid-cycle
• Door not latching properly
• The dryer continuing to run with the door open

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

O-rings are used in various locations and applications to seal and protect connections throughout the engine. The O-ring is typically used for rigid connections where a proper seal is required for optimal functioning. It is critical to have the right size and style of O-ring installed for proper operation. These parts tend to wear over time and that can affect their ability to seal. If O-rings are degraded or damaged in any way, they need to be replaced as soon as possible to prevent further damage. This O-ring is manufactured to exact specifications by Briggs & Stratton to provide a genuine OEM replacement. It can be used in various Toro, Briggs & Stratton, and Lawn-Boy engines. Typically found in lawn tractor engines, this part is compatible with more than 150 machines. This O-ring is made from durable materials and sold individually. Always disconnect the spark plug before beginning engine work and wear gloves for hand protection.