Parts for Ge AEE08ATL2: Room Air Conditioner Parts

This curtain assembly is the factory replacement trim piece that restores the original fit and finish of the appliance's front opening. It helps cover gaps and keeps the front area looking and functioning as intended. What it does

• Replaces a damaged, bent, or missing front curtain/trim to restore proper appearance
• Helps block light, debris, and drafts from the appliance opening
• Maintains alignment and surface coverage for adjacent components
• Prevents further wear to surrounding trim and seals caused by gaps

• One curtain assembly/trim piece

• Disconnect power (and gas, if applicable) before servicing to avoid shock or injury
• Handle edges carefully to avoid cuts; use proper tools and fasteners removed from the original part
• Secure all clips/screws to ensure a correct fit

This top guide sub-assembly helps guide and support the washer/dryer top panel so it opens, closes and sits correctly. It restores smooth top-panel movement and reduces binding or misalignment during use. What it does:

• Guides the appliance top panel along its track for correct alignment and smooth movement
• Prevents the top panel from catching, scraping or sticking when opened or closed
• Helps reduce noise or vibration caused by a loose or worn guide
• Restores proper fit and prevents uneven gaps around the top panel

• One top guide sub-assembly

• Disconnect power to the appliance before servicing
• Remove any screws or clips securing the top panel to access the old guide
• Replace the guide using existing fasteners; do not force parts into place
• If clips or hardware are damaged, replace them before completing reassembly

This axial flow fan circulates air inside the appliance to help cool components and maintain proper ventilation. It replaces a worn or damaged blower wheel to restore airflow and reduce overheating risk. What it does:

• Moves air across coils or internal components to support cooling and ventilation.
• Helps prevent overheating and supports consistent appliance performance.
• Can reduce unusual temperature-related symptoms or poor cooling/airflow.
• Fits into the appliance's blower/motor assembly to restore proper airflow.

• Disconnect power to the appliance before starting any repair.
• Handle the fan blades carefully to avoid bending or damage.
• Verify proper seating on the motor shaft and secure fasteners per the appliance's service instructions.

This heater cover protects the dryer's heating element assembly and helps direct airflow for efficient drying. It prevents direct contact with heating components and supports safe, reliable operation of the heater area. What it does:

• Encloses and shields the heating element assembly to prevent accidental contact.
• Helps channel airflow over the element for consistent heat transfer.
• Keeps lint and debris away from the heater, reducing risk of localized overheating.
• A damaged or missing cover can cause unusual odors, visible scorch marks, or intermittent heating.

• Disconnect power (unplug or switch off breaker) before starting service.
• Allow the appliance to cool completely before accessing the heater area.
• Basic hand tools (screwdriver, nut driver) typically required; follow the factory service manual for disassembly.

This electric heating element replaces a failed oven/range heating component to restore bake and broil heat. It installs in the oven cavity and provides the radiant heat needed for cooking. What it does

• Heats the oven cavity so the appliance can reach and maintain cooking temperatures
• Commonly replaces elements that glow but fail to produce enough heat
• Resolves symptoms like no heat, uneven baking, or oven not reaching set temperature
• Connects to existing terminal screws/wire harness for direct replacement

• Disconnect power at the breaker before starting any repair
• Allow the oven to cool completely and wear gloves to avoid sharp edges
• Remove the oven racks and access panels for clear access to the element mounting screws and terminals
• Tighten terminal screws securely and test operation after reassembly

This main control board powers and coordinates the appliance's electronic functions so your range/oven control responds correctly. It replaces a failed or unresponsive control module to restore normal electronic operation. What it does:

• Receives user commands and runs the oven/range control logic and display functions
• Manages heating cycles, timers, and safety interlocks controlled by the front panel
• Commonly replaces a board that causes unresponsive buttons, erratic display, or failure to start heating
• Helps resolve intermittent operation or electronic error codes tied to the control board

• Disconnect power at the breaker before accessing or replacing the board to avoid shock
• Handle the board by the edges and avoid touching components to prevent ESD damage
• Some wiring harnesses plug into the board; label connectors or take a photo before disconnecting

This indoor air thermistor is a refrigerator air temperature sensor that helps the control board monitor cabinet temperature for proper cooling performance. Replacing a failing thermistor restores accurate temperature sensing to help prevent spoilage and cycling issues. What it does:

• Senses interior air temperature and sends temperature signals to the fridge control board
• Helps the compressor and fans run at the correct times for stable cooling
• Commonly associated with symptoms like warm or fluctuating temperatures, excessive cycling, or cooling that never reaches the set point
• Works as part of the temperature control system—faulty sensors can cause incorrect defrost or cooling behavior

• Disconnect power to the appliance before accessing or replacing the sensor
• Handle the sensor lead and element carefully to avoid damage; avoid pulling on wires
• Reinstall in the original location and routing; secure connectors fully to ensure good electrical contact

This room temperature sensor measures interior air temperature so the refrigerator can regulate cooling cycles and keep food fresh. Replaces a failed thermistor to restore accurate temperature readings and stable cooling. What it does:

• Senses refrigerator cabinet air temperature and sends a signal to the control board
• Helps the control board cycle the compressor and fans correctly for consistent cooling
• Commonly fails when you see warm or inconsistent temperatures inside the fridge
• Can cause the unit to run too long or not cool if the sensor reads incorrectly

• One room temperature sensor (thermistor) as shown

• Disconnect power to the appliance before replacing the sensor to avoid shock
• Handle the sensor and connector carefully; do not tug on wiring
• Mount and route the sensor per the manufacturer's location—replace in same position for accurate readings

This replacement air filter for room air conditioners screens dust and lint from incoming air to protect the indoor coil and maintain airflow, helping your unit cool as designed. What it does:

• Traps dust and lint before they reach the evaporator coil
• Helps maintain proper airflow and cooling performance
• Replaces a missing, damaged, or excessively dirty filter
• Typical symptoms include weak airflow, reduced cooling, longer run times, or a visibly clogged filter

• Includes 1 air filter

• Disconnect power before servicing
• Open or remove the front grille to access the filter slot
• Slide out the old filter; insert the new one matching the original orientation; ensure it is fully seated
• Do not operate the unit without a filter installed

Front panel assembly replaces a damaged or worn control panel to restore the appliance's appearance and provide a secure mounting surface for control buttons and displays. What it does:

• Provides the finished exterior for the control area and protects internal components from everyday wear and impact.
• Supports and secures control knobs, buttons and display components so controls operate correctly.
• Restores cosmetic appearance when the original panel is cracked, dented or heavily scratched.
• Helps prevent loose or misaligned controls caused by a damaged front panel.

• Disconnect power to the appliance before beginning any work to avoid risk of electrical shock.
• Access typically requires removing the control console or surrounding trim; keep track of screws and clips during disassembly.
• Handle edges and painted surfaces carefully to avoid scratching; some parts may need to be transferred from the old panel.

A hardware assembly used to secure and align internal components during appliance installation. Restores proper mounting and reduces movement for a safer, more stable fit. What it does:

• Provides the mounting hardware needed to fasten appliance panels or components
• Helps stop rattling, sagging or misalignment caused by loose or missing fasteners
• Restores structural support for doors, trim, or internal brackets
• Replaces worn or damaged installation hardware to improve fit and function

• One hardware assembly for installation

• Follow the OEM diagram when installing
• Disconnect power and any fuel supply before starting work
• Use appropriate tools and torque; replace any damaged fasteners