Roper Range / Cooktop / Oven Parts

Color: Black. Includes two double grates.

The Oven Liner Touch Up Paint is an OEM part for Whirlpool ovens. This 2 oz warm white touch-up paint is designed to cover minor scratches, chips, and blemishes on the oven liner, restoring its appearance and protecting it from further damage. 

Causes of a bad oven liner include exposure to high temperatures, accidental impacts, and abrasive cleaning materials, which can lead to scratches, chips, and discoloration. Over time, these imperfections can worsen, making it necessary to use touch-up paint to maintain the oven liner’s integrity.

Symptoms of a bad oven liner include:

• Visible scratches or chips on the oven interior
• Discoloration or fading of the liner
• Increased difficulty in cleaning the oven liner
• Potential rust or corrosion in affected areas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

Small rubber bumper that cushions appliance components to reduce noise, prevent metal-on-metal contact, and protect finishes; replaces worn or missing bumpers to restore quiet operation and prevent damage. What it does:

• Absorbs shock and vibration to stop rattling or buzzing
• Prevents doors, drawers or panels from banging or scraping
• Protects painted and metal surfaces from wear and chipping
• Helps restore proper spacing and alignment of moving parts

• Always disconnect power to the appliance before servicing
• Typically installs by pressing into a mating hole or seating on a flat surface; some applications use adhesive
• Inspect mating surface for damage or debris and replace any additional worn bumpers for even contact

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

The thermostat bulb clip is an OEM component specifically designed for Whirlpool drop-in electric ranges, securely fastening the thermostat sensor bulb. This clip features corrosion-resistant spring coils and precision tips.  

Symptoms of a bad thermostat bulb clip include:  

• Dangling thermostat bulb
• Temperatures inside oven might be incorrect because sensor bulb is not mounted correctly.

Causes of failure involve metal fatigue weakening the thermostat bulb clip over years of expansion and contraction during heating, worn surfaces losing grip, or damaged barbs failing to anchor the thermostat bulb.

Replace yours today with this genuine OEM Whirlpool clip. Compatible with Jenn-Air, GE, and select Kenmore appliances, reinforced coils maintain constant tension assuring safety. Reliable glass retention enhances interior illumination for tasks.

This metal refrigerator door hinge secures and pivots the appliance door so it opens and closes smoothly, helping maintain a tight seal and proper door alignment for reliable cooling. What it does

• Supports the refrigerator door and provides the pivot point for opening and closing
• Keeps the door aligned to help the gasket seal and maintain interior temperature
• Worn or damaged hinge can cause the door to sag, rub, make noise, or not close fully
• Replacing a bent or broken hinge restores proper door movement and alignment

• Disconnect power to the appliance before starting any repair
• Use proper tools and support the door when removing or installing the hinge to avoid dropping or bending the door
• Check related fasteners and mounting surfaces for damage and replace if needed

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This conversion orifice spud kit contains three precision orifice spuds used to change the gas flow profile for compatible cooktop/oven burners. It helps restore correct burner flame size and performance after a fuel-type conversion. What it does:

• Replaces worn or incorrect orifice spuds to set proper gas flow for burner operation
• Used in fuel-type conversion to match burner jets to the correct gas pressure/type
• Can resolve uneven or weak flames and burners that won't reach expected heat
• Works with each burner where a standard orifice spud is specified

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Installation may require burner removal and a proper wrench or driver for the spuds
• After installation, check all fittings for leaks using a gas leak detector or soapy water

Seal tape restores a tight seal around appliance doors and panels to help prevent air or moisture leaks and improve temperature stability. Use it to replace worn or missing sealing strips that allow drafts, frost, or heat loss. What it does

• Creates a flexible barrier to close small gaps and reduce airflow or moisture migration at door and panel seams.
• Helps maintain correct internal temperatures and can reduce frost buildup or inefficient cooling/heating.
• Replace when tape is cracked, compressed, detached, or visibly deteriorated.
• Commonly used where a thin, form-fitting sealing strip is needed on appliance doors and access panels.

• One seal tape.

• Clean and dry the mating surface before installing for best adhesion; remove old residue.
• Cut to fit and press firmly along the length to seat the tape; trim excess as needed.
• Disconnect power (unplug or switch off breaker) before starting.

This burner ignitor switch controls spark delivery to a cooktop burner so the burner lights when the knob is turned. It replaces a worn or failed switch to restore ignition responsiveness and consistent sparking. What it does:

• Routes spark current to the surface burner ignitor when the control knob is turned
• Stops spark delivery when the control knob is released or turned off
• Commonly used when a burner fails to spark or sparks intermittently
• Works with the cooktop's ignition system to enable safe, reliable lighting

• One burner ignitor switch

• Disconnect power (and gas if applicable) before servicing to avoid shock or injury
• Access may require removing the cooktop or control panel
• Verify wiring and switch operation with a multimeter before replacement

This broiler pan finish is the replacement inner tray that restores the cooking surface and drip collection for oven broiling. It provides a durable surface for even browning and helps contain juices for easier cleanup. What it does:

• Replaces a worn, warped, or damaged broiler tray surface to improve broiling performance
• Collects drippings and prevents them from falling onto the oven bottom
• Helps food brown and sear more evenly by providing a stable cooking surface
• Reduces smoke from burned-on residue when the surface is restored

• Install by seating the finish tray into the broiler pan assembly per your oven's service manual
• Ensure the oven is completely cool and disconnected from power before servicing
• Handle edges carefully; use gloves if metal edges are sharp

Color: White.

Color: White. Size: 13 oz. Spray paint primer. can.

Left hand side. For right hand use 98004953

This replacement power cord restores the appliance's main AC connection so it can receive power safely. Use this cord when the original cable is frayed, cut, melted, or otherwise damaged to prevent intermittent power or electrical hazards. What it does:

• Replaces the appliance's factory power cable to restore reliable electrical connection.
• Transmits mains power from the outlet to the appliance's internal wiring and controls.
• Addresses symptoms such as no power, intermittent power loss, visible cord damage, or burn/melt marks at the cord or plug.
• Helps prevent electrical arcing or shorting caused by damaged insulation or exposed conductors.

• Disconnect the appliance from power at the breaker or unplug before starting any work.
• Verify the cord matches the appliance's connector and routing; do not modify cord ends or splices.
• Secure all strain reliefs and terminal connections per the appliance's service instructions.