Dishwasher Handle Screw Parts

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

With your part thanks Read more

Removed Torx screws inside the dishwasher door, this causes the door panel to fall forward/down. Having a rug or something underneath to prevent scratches is useful. It's about 8 screws that need to come out, if I recall correctly they are all the ones with the torx head facing into the dishwasher when in the closed position. Then the panel comes off, exposing the bolts holding the handles, the cap comes off easily and replaces easily and reverse the process. Some of the screws are different... Read more

In order to replace this, you must remove the "outer door". This service manual is a pretty good reference (page 37): http://members.msaworld.com/wp-content/uploads/sites/3/2017/02/2013-DW-Service-Manual.pdf Note that this specific dishwasher has 12 screws that need to be removed before the outer door can be separated. Once separated, don't even bother trying to push the broken handle out of the front as suggested. You will probably end up damaging the outer door. Instead, take some... Read more

• Door won't close

I found the door switch was not making contact when the door closed. I adjusted it, but then it would not open so the dishwasher would run when the door wasn't closed. The contacts were too long in the switch so they would bend and stay together when the door opened. The original switch was very poorly made for a very expensive Maytag dishwasher. The new switch you supplied was much better quality and easily replaced the one that was installed at the factory. I was a little baffled at the... Read more

• Won't start
• Door latch failure
• Door won't close

I turned off the power then removed the six or so screws from the back of the top panel. I marked the two front wires on the latch with tape so I would not get them confused. I removed the two screws holding the latch on--these take a six pointed star bit on the screw driver--the bit is in most screw driver sets with interchangeable heads. I then connected the wires to the new latach and put everything back together. The whole process took between ten and fifteen minutes. Read more

I easily found the replacement part on the Appliance Parts Pros website and ordered (2), one for each end of the handle and yes it is the same part for either side. They showed up a few days later. I had seen a video of how to expose the handle screws behinf the door face. I backed out the appropriate (6) Torx screws and the front of the dishwasher door came right off exposing the handle screws. (Note: This model of dishwasher is well engineered as the door face is completely separated from the... Read more

• Door latch failure

After finding the model number for my dishwasher, I looked on line for the part and ordered it. The part arrived next day. I was a little hesitant to tackle it myself, as I am a 67 year old female. However I decided I could do it and was all set until I found out that I needed a Torx screwdriver. This however was not going to stop me. At a trip to my neighbor I was able to find bit for a drill that would let me remove one screw. The next stop was to my favorite hardware store where I... Read more

• Won't start

After searching for hours online, I finally found a you tube video called: Diagnose & Repair a Bad Latch on a Frigidaire Dishwasher (GLD2250RDC4) . His explanation and directions were sooo easy and it worked! So I didn't have to call a repairman or buy a new control panel and the part cost $30.00, Easy! Read more

Followed instruction I saw on a you-tube video. Was quick and easy. Read more

After having seen the video I installed the new lid and it worked. Read more

I got on the site and shared my issue. It was determined my door switches were bad, as well as my actuator. I ordered the parts (which arrived in just 2 days!) and I fixed it myself in just under 10 minutes, for under $30.00. Thanks guys!!!! Read more

• Won't start

Replaced with new latch, took about 5 minutes. T25 torx screwdriver and flathead screwdriver needed. Read more

Heating element nut had cracked causing a leak. Rather than run right out and buy a new one, I found the cracked nut and replaced it for about 11.00. Thank you Appliance pros. Quick shipping. Read more

The old fascia had broken and been torn off. I should have saved the buttons from it, but I didn't know that I'd be repairing it - I figured I would have to replace the unit. Well, money is tight, so I got the model number from the unit and looked up parts online. I couldn't find the exact model number on this site, but the picture of the fascia looked just like the picture in my manual, so I bought it, a handle strip, and a new set of buttons. I pulled the stainless panel off the front, then... Read more

Repair estimate was $250 parts, $250 labor to change out the circulating pump. I decided to do it myself. Pump was $166 from AppliancePartsPros. It arrived in 4 days. I looked at the video on their website, followed the instructions step by step and did it myself. They estimated 45 minutes. It took 2 hours.There are always minor differences so always take photos of yours. Suggest that you bag up all screws and pieces from each part as you take them off and label the bag. I had 12 bags with 2 to... Read more