Dishwasher Lid Lock Latch Parts

The part went on easily. U Tube video answered any questions I had before installing. Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

Removed Torx screws inside the dishwasher door, this causes the door panel to fall forward/down. Having a rug or something underneath to prevent scratches is useful. It's about 8 screws that need to come out, if I recall correctly they are all the ones with the torx head facing into the dishwasher when in the closed position. Then the panel comes off, exposing the bolts holding the handles, the cap comes off easily and replaces easily and reverse the process. Some of the screws are different... Read more

In order to replace this, you must remove the "outer door". This service manual is a pretty good reference (page 37): http://members.msaworld.com/wp-content/uploads/sites/3/2017/02/2013-DW-Service-Manual.pdf Note that this specific dishwasher has 12 screws that need to be removed before the outer door can be separated. Once separated, don't even bother trying to push the broken handle out of the front as suggested. You will probably end up damaging the outer door. Instead, take some... Read more

• Door won't close

I found the door switch was not making contact when the door closed. I adjusted it, but then it would not open so the dishwasher would run when the door wasn't closed. The contacts were too long in the switch so they would bend and stay together when the door opened. The original switch was very poorly made for a very expensive Maytag dishwasher. The new switch you supplied was much better quality and easily replaced the one that was installed at the factory. I was a little baffled at the... Read more

Tried CLR to remove hard water deposits. That did not help. Ordered new dispenser. The GE series that the detergent module fits in was a little difficult to open. Finally found a video explaining the whole door had to come off in order to open it up to replace the module. Works great now. Read more

• Will not dispense detergent

Process was a bit more complicated than the videos I had watched online. Had to remove both front panel and control panel to get to soap dispenser. Removed wires to soap dispenser and rinse aide dispenser. Removed wire "harness" around the top and right side of dispenser. Pried back the clips to allow dispenser to be pushed out. It was helpful to have another person to hold the door open at this point. Bent clips back and reinstalled everything. New part works great. Read more

Replaced dispenser Read more

• Will not dispense detergent

I ordered the part, looked at a YouTube instructional video on how to do it, and did it myself. It wasn't too hard, and I have no experience. I received the part very quickly! Read more

My husband expected we needed a new dishwasher but I insisted on trying to fix it first. You need a Torx screwdriver so make sure you have a set. A little difficult to get cover back on and lined up by myself, but I managed and this was my first attempt at major appliance repair. I replaced the entire console and the dispenser. Still working after 3 loads so my husband may have to eventually admit that I fixed it. Read more

Twist the old one out, insert tab, twist until other side snaps in. Easy as pie after watching the video! Read more

• Won't start
• Door latch failure
• Door won't close

I turned off the power then removed the six or so screws from the back of the top panel. I marked the two front wires on the latch with tape so I would not get them confused. I removed the two screws holding the latch on--these take a six pointed star bit on the screw driver--the bit is in most screw driver sets with interchangeable heads. I then connected the wires to the new latach and put everything back together. The whole process took between ten and fifteen minutes. Read more

First unplug or turn off the electrical breaker to the dishwasher. Then I removed the phillips head screws holding the inner door to the outer door panel. I then removed the hex head screws holding the dispenser assembly. The electrical connection needs to be disconnected and then reverse the procedure to install the new dispenser. Restore power to the dishwasher and your done. Read more

I easily found the replacement part on the Appliance Parts Pros website and ordered (2), one for each end of the handle and yes it is the same part for either side. They showed up a few days later. I had seen a video of how to expose the handle screws behinf the door face. I backed out the appropriate (6) Torx screws and the front of the dishwasher door came right off exposing the handle screws. (Note: This model of dishwasher is well engineered as the door face is completely separated from the... Read more

• Will not dispense detergent

I ordered a new soap dispenser and began a new venture in repairing my dishwasher. I turned off the breaker that suppled power to the unit. I removed all the T-15 torx screws from the inside cover except one, which my wife helped me hold in. This prevents the cover from dropping off. Then, after removing those two, we closed the dishwasher cover, and lifted off the outside cover. That being off, I saw the two wires connecting the dishwasher dispenser solinoid. Removed them. Notice, that one... Read more

As a homeowner, I love that I can just type my model number into Appliance Parts Pros website and find a listing/diagram of the entire unit. So when my dispenser on my dishwasher broke, I just ordered a new one. I use You Tube to watch videos on the specific repair, and then VOILA! I do the repair myself, saving at least a hundred dollars in a repair persons service call charge! While this repair was for my dishwasher, I've also fixed my washing machine, dryer, and steam humidifier. Read more