Dryer Push Button Start Switch Parts

Fix a dryer that overheats or won't heat properly with a new temperature switch. Controls heat settings across multiple cycles. DIY-friendly repair.

White plastic insert that snaps into your washer's control knob. Restores a clean, finished appearance when the original is cracked, discolored, or missing.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

Decorative cover ring that surrounds the dryer timer dial, providing labeled settings. Replace if cracked, broken, or worn from frequent use.

Timer knob assembly mounts to the control shaft for manual cycle selection. Replaces a cracked, worn, stripped, or missing knob on your laundry center.

This replacement control knob assembly restores a solid, accurate feel when selecting settings on your appliance. Replace cracked or stripped knobs to regain smooth control and a clean, like-new appearance.

• Interfaces with the control shaft so you can select functions and settings
• Common failure signs: cracked or broken knob, stripped insert, wobbly fit, falls off, hard to turn, or missing knob
• Restores proper grip and pointer alignment for accurate adjustments
• Direct replacement engineered to match the original fit and function

• Disconnect power and allow any hot surfaces to cool before servicing
• Pull the old knob straight off the control shaft; avoid prying on the control panel
• Align the shaft/keyed flat with the new knob and press firmly until fully seated
• Verify smooth operation through the full range of settings

This timer knob mounts on the appliance's mechanical timer shaft and lets you select cycles and settings. Replace a cracked or stripped knob to restore smooth, positive control of the timer and accurate cycle selection.

• Attaches to the timer shaft so you can set cycle and time
• Provides a secure grip for selecting and adjusting settings
• Common symptoms: knob spins without moving the timer, feels loose, cracked, or missing
• Helps restore proper engagement when the hub is worn or stripped

• Disconnect power before servicing
• Pull the old knob straight off the timer shaft
• Align the flat/splines of the new knob with the shaft and press on firmly
• Rotate through a full turn to confirm proper engagement

This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.

Fix a dryer that won't start or starts intermittently with this start switch replacement. Restores the start circuit for reliable operation. Easy DIY fix.

Color: gray. The back part of the knob measures about an inch in diameter, and the front part with the handle is about 2 inches in diameter.

Dryer won't start when you press the button? This push-to-start switch closes the circuit to begin cycles. Easy DIY repair restores reliable starting.

Replacement control knob for dryer control panels. Restores grip and accurate setting selection when original knob is cracked, worn, loose, or missing.

Replace a cracked, broken, or missing control panel push button cap on your dishwasher or dryer. Restores clean appearance and reliable button feel.

Dryer won't shut off in auto dry or only heats on one setting? This temperature switch restores proper heat level control. DIY-friendly repair.

Replacement control knob for dryers and washers. Installs on the control panel to adjust settings. Replace worn, broken, or missing knobs for reliable use.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling