Dryer Run Vent Push Button Switch Parts

White plastic insert that snaps into your washer's control knob. Restores a clean, finished appearance when the original is cracked, discolored, or missing.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

Dryer won't start but lights work? A faulty door switch prevents operation. This replacement switch restores normal function in under 10 minutes.

This dryer blower housing encloses the blower wheel and directs air from the drum through the lint filter to the exhaust vent. Replacing a damaged housing restores proper airflow for consistent drying and helps keep lint contained within the airflow path.

• Encloses and supports the blower wheel while channeling air from the drum to the exhaust
• Maintains correct airflow and back pressure for efficient drying performance
• Replace if the housing is cracked, warped, melted, or otherwise damaged
• Typical symptoms include weak vent airflow, longer dry times, rattling or scraping from the blower area, or visible lint leakage

• Disconnect power; if gas, also shut off the gas supply
• Access the blower area by removing the lower/front panel and lint ducting as required by your model
• Transfer the blower wheel and any brackets from the old housing; clean lint from ducts before reassembly
• Ensure the housing seats fully and all duct connections are tight; spin the blower by hand to verify clearance before restoring power

This is a small electrical switch mounted near the dryer door opening that detects whether the door is open or closed. It completes the circuit that allows the dryer to run when the door is shut. Replace this switch if your dryer won't start, stops mid-cycle, or runs with the door open.

Routes airflow inside your dryer to maintain circulation and temperature. Replace if cracked, warped, rusted, or blocked to restore proper air path.

This is the duct assembly - sometimes called the heater box - that houses or channels heated air from the heating element into the dryer drum. It directs airflow so clothes dry efficiently and evenly. Replace this assembly if it is cracked, warped, or damaged, which can cause poor drying performance, unusual noises, or overheating issues.

Dryer duct that routes hot air through the ventilation system. Replace if cracked, warped, scorched, or causing debris to attach to clothing during cycles.

6-foot flexible metal duct connects dryer exhaust to wall vent. Replace if crushed, torn, disconnected, or missing to restore proper airflow path.

Relocates your dryer's exhaust vent from rear to left, right, or bottom. Includes elbows, duct, and instructions. Replace when changing installation.

Decorative cover ring that surrounds the dryer timer dial, providing labeled settings. Replace if cracked, broken, or worn from frequent use.

Timer knob assembly mounts to the control shaft for manual cycle selection. Replaces a cracked, worn, stripped, or missing knob on your laundry center.

This timer knob mounts on the appliance's mechanical timer shaft and lets you select cycles and settings. Replace a cracked or stripped knob to restore smooth, positive control of the timer and accurate cycle selection.

• Attaches to the timer shaft so you can set cycle and time
• Provides a secure grip for selecting and adjusting settings
• Common symptoms: knob spins without moving the timer, feels loose, cracked, or missing
• Helps restore proper engagement when the hub is worn or stripped

• Disconnect power before servicing
• Pull the old knob straight off the timer shaft
• Align the flat/splines of the new knob with the shaft and press on firmly
• Rotate through a full turn to confirm proper engagement

This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.

Color: gray. The back part of the knob measures about an inch in diameter, and the front part with the handle is about 2 inches in diameter.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling