Washer Panel Control Knobs Parts

Fix a washer that won't advance through cycles or gets stuck washing or spinning. This control timer regulates cycle progression. Moderate DIY repair.

Fix a washer that won't start, shows error codes, or won't advance cycles. This electronic control board manages timing and power to components.

If your washer won't start, keeps beeping, or shows error codes, the control board may have failed. This computer manages all washer functions.

Washer won't start, shows error codes, or cycles incorrectly? The control board manages all wash cycles and safety functions. Moderate DIY repair.

Washer won't start or advance through cycles? This control board assembly restores cycle selection and timing. Moderate DIY repair for 4-cycle models.

Control panel touch pad for washers. Houses the digital display and membrane buttons for cycle selection. Replace if faded, cracked, or unresponsive.

This replacement top panel restores the appliance's upper surface and protects internal components while giving a clean, finished appearance. Ideal when the factory top is dented, rusted, or otherwise damaged. What it does:

• Covers and protects internal components located beneath the top panel
• Provides a flat, finished surface for user access and controls
• Restores proper alignment and fit where the original top is bent or corroded
• Helps stop drafts, debris, or moisture from entering the cabinet area

• One top panel

• Disconnect power (and gas, if applicable) before starting any repair
• Handle edges carefully; use gloves to avoid cuts
• Reuse mounting hardware only if in good condition; replace damaged fasteners

This mechanical cycle timer controls the sequence and duration of washer operations. Replacing a failing timer restores proper advancement through fill, agitate, drain, and spin so cycles complete reliably with accurate timing. What it does:

• Advances the washer through each step by routing power to the water valves, motor, and drain pump at the correct times
• Sets the length of each stage for consistent operation
• Common failure signs: cycle won't advance or stops mid-cycle
• Timer knob doesn't move or must be jiggled to run
• Skips functions (no agitate, drain, or spin) while others still work

• 1 mechanical timer assembly

• Disconnect power before servicing; access the timer from the control console
• Take photos or label wires; transfer them to the new timer one at a time to maintain correct positions
• Reuse the existing knob and dial; align the timer shaft properly and secure the mounting screws
• After reassembly, run a short test cycle to ensure proper advancement

If your washer won't advance through cycles automatically and you must turn the knob manually, the timer likely failed. Moderate DIY repair restores function.

Fix washer won't start, stops mid-cycle, or skips rinse with this electronic control board. Moderate DIY repair with connector-based installation.

If your washer shakes excessively or stops mid-cycle, the accelerometer sensor may be faulty. This part monitors vibration levels to regulate spin speed.

Fix a washer stuck on rinse or spin cycle with this electronic control board. Restores responsive controls and accurate cycle timing. Moderate DIY repair.

This UI board assembly replaces the refrigerator's user interface/control board to restore button response and display feedback. It lets you reliably set temperatures and modes so the appliance accepts and shows commands correctly. What it does:

• Receives and processes user inputs from the control panel (buttons/touchpad) so selections register and run.
• Drives the front display and indicator lights so temperature, mode and status information is visible.
• Replaces a failed or intermittent interface that causes unresponsive controls, blank or garbled display, or incorrect status indications.
• Works with the main control to pass commands; replacing the board can isolate interface-specific failures.

• Disconnect power to the appliance before starting — this part is electronic and may be damaged by live power.
• Take photos of existing wiring and mounting before removal to ensure correct reassembly.
• Handle the board by its edges and avoid static discharge; use anti-static precautions if available.
• Reconnect all plugs securely and test functions before fully reinstalling trim or covers.

This inverter assembly is the control module that powers and regulates the refrigerator compressor, restoring variable-speed operation and helping maintain proper cooling. Install to replace a failed or damaged inverter module. What it does

• Converts and supplies the correct power signals to the compressor so it can run at variable speeds
• Can eliminate error codes or fault indicators related to the inverter/control module
• May reduce abnormal compressor noise or intermittent compressor operation when the inverter is faulty

• One inverter assembly

• Disconnect power at the breaker before starting work
• Handle the board and connectors with care; avoid static discharge and damaged wiring
• Verify connector orientation and secure all plugs before reapplying power

Fix a washer that won't advance cycles or start filling water with a new timer. Controls cycle timing and electrical components. 10-15 minute DIY repair.

Fix a washer that won't start, fill, or advance cycles with this control board. Controls all washing machine functions and cycle settings.