Washer has a burning smell: Common Causes & How to Fix

Disconnect power. Turn off power at breaker box before working on machine.

Remove outer tub. Find securing screws around edges and pull tub away from housing to access inside.

Disconnect wires from stator. Note wire positions so they can be reconnected properly later.

Remove stator retaining bolts. A few bolts usually secure stator to inside of tub.

Pull stator and attached rotor out. Gently wiggle assembly from tub once bolts are removed.

Clean tub mounting area. Wipe away any debris from where new stator will attach.

Attach new stator and rotor. Set assembly into position inside tub and start bolts by hand.

Reconnect stator wires. Match colors to labeled terminals on replacement part.

Replace outer tub. Slide tub back into position and secure edges with screws.

Test machine functions. Reconnect power and run short spin cycle to check new kit.

Troubleshoot if needed. Check connections if machine does not operate as expected.

Unplug the washing machine. Disconnect power to avoid electric shock.

Access the control board. Remove the back service panel to locate the motor control board.

Label wire connections. Take note of where all the wiring harnesses connect to the control board.

Disconnect wires. Detach all the wire harnesses by hand or using pliers.

Remove mounting screws. Use a screwdriver to remove any screws securing the control board.

Remove old control board. Carefully detach the old motor control board from the washing machine.

Install new control board. Align the new motor control board and reinsert the mounting screws.

Reconnect wiring. Attach all the wiring harnesses to the correct terminals on the new control board.

Replace service panel. Reattach the back service panel once done.

Restore power. Plug in the washing machine.

Test operation. Run a test cycle and check that the motor functions properly before regular use.

Troubleshoot issues. If the motor still does not operate right, double check the wiring connections.

Unplug the washing machine. Disconnect the power cord before servicing to prevent electric shock.

Open the control panel. The control board is located behind the control panel on the washer front.

Label connections. Take note of where each wire and connector is attached to the control board.

Disconnect wires. Carefully detach all wiring harnesses and connectors from the board.

Remove mounting screws. Use a screwdriver to remove any screws securing the control board.

Remove control board. Carefully pull the control board free from the washer once all wires are detached.

Install new control board. Align the replacement board into position and insert mounting screws.

Reconnect wires. Attach all wiring harnesses and connectors to the matching terminals on the new board.

Close control panel. Carefully close the control panel once the new board is installed.

Restore power. Plug in the washing machine and test operation.

Program control board. You may need to program or configure the new control board if it doesn't operate correctly.

Test cycles. Run short test cycles to verify the washer is functioning properly before regular use.

Shut off power at breaker box. Turn off power for safety before working.

Remove outer tub or rear panel. Find securing screws to access inside of machine.

Locate motor pulley and spin pulley. The pulleys the belt loops around.

Loosen idler pulley. A bolt adjusts tension, loosen to relax belt for removal.

Take off old belt. Twist and wiggle belt off pulleys, may need to pivot parts.

Clean any debris from pulleys. Wipe surfaces so new belt slides smoothly.

Install new belt. Loop belt around motor pulley, then spin pulley and idler.

Adjust idler pulley bolt. Tighten bolt just enough for belt to have proper tension.

Replace outer tub or rear panel. Secure with screws removed earlier.

Reconnect power and test machine. Run cycle to check new belt functions properly.

Inspect belt after cycle. Make sure the belt remains in place and hasn't slipped pulleys.

Unplug washing machine. Locate the plug on the back of the machine and disconnect from power source to prevent electric shock.

Unplug the washing machine. Disconnect the power cord for safety.

Access the belt. Remove the back service panel to access the motor and belt assembly.

Locate the belt. Identify the rubber drive belt that connects the motor pulley to the drive pulley.

Loosen motor mount. Use a wrench to loosen the bolts on the motor mounting bracket.

Remove old belt. Slip the old belt off the motor and drive pulleys. You may need to pivot the motor to get slack in the belt.

Install new belt. Loop the new belt around the pulleys, ensuring it is properly seated in the grooves.

Retighten motor. Tighten bolts on motor mount bracket to secure in place.

Reattach service panel. Replace the back service panel.

Restore power. Plug washing machine back in.

Test operation. Run a short test cycle with no clothes to verify smooth operation.

Adjust belt tension. If the belt is loose, pivot motor slightly to increase tension and prevent slipping.

Shut off power. Turn off electricity to the washer at the circuit breaker or unplug it before servicing electrical components.

Remove outer panel. Detach any outer covers or casings blocking access to the timer module inside using a screwdriver.

Disconnect wires. Note the wire colors and locations before disconnecting all electrical wires from the old timer terminals.

Remove mounting screws. A few screws typically secure the timer module to the inside of the washer cabinet. Remove them.

Withdraw old timer. Once fully detached from wires and frame, gently lift out the old timer control module straight away.

Insert new timer. Set the replacement module into the vacant space, aligning any mounting holes if present.

Reattach wires. Reconnect each wire to the properly colored terminal on the new timer, referring to notes if needed.

Refasten module. Replace the mounting screws to securely fix the timer into position inside the washer.

Refit covers. Slide outer panels back into place to conceal repairs before restoring power.

Test washing cycles. Run various cycles to ensure the new timer is functioning normally.

Unplug washer and secure access. Disconnect power and open rear or bottom panel for protected access.

Unplug the washing machine. Disconnect power to avoid electric shock.

Access the pulley. Remove the back service panel to locate the drive pulley.

Loosen set screw. Use an Allen wrench to loosen the set screw securing the pulley to the drive shaft.

Remove pulley. Slide the old pulley off the drive shaft. You may need a pulley puller tool.

Clean shaft. Remove any oil, dirt or debris from the drive shaft.

Install new pulley. Slide the new pulley onto the drive shaft until fully seated.

Tighten set screw. Tighten the set screw against the flat of the drive shaft to secure.

Check alignment. Make sure the pulley is properly aligned with the motor pulley.

Replace service panel. Reattach the back service panel.

Restore power. Plug washing machine back in and test operation.

Test spin cycle. Verify smooth rotation when running a spin cycle with no load.

Disconnect power. Turn off breaker to remove power from machine.

Remove outer tub or back panel. Locate securing screws to access internal components.

Take photographs of wiring. Take detailed pictures of all wire connections before removal.

Disconnect all wires from harness. Note labels/colors to ensure proper reconnection later.

Remove harness retaining screws. Look along edges or back of wiring housing for screws.

Detach old harness from machine. Flexible harness can now be gently removed.

Clean mounting area of residue. Wipe where new harness will attach inside housing.

Mount replacement wire harness. Set housing into position and start retaining screws.

Reconnect wires one by one. Reference photos and labels to match wires correctly.

Reinstall rear panel or outer tub. Replace any removed screws or parts.

Reconnect power and test functions. Run cycle while double checking all wires connected.

Inspect harness after test. Mkae sure it is securely mounted and all wires remain attached.

Disconnect power at breaker box. Turn off power before servicing machine.

Remove rear panel or outer tub. Locate securing screws to access internal components.

Take photographs of wire connections. Document positions for accurate reconnection.

Disconnect wires from old board. Note labels to properly reconnect them later.

Remove mounting screws. A few screws usually hold board securely inside machine.

Detach old inverter board from frame. Carefully lift it out once fully disconnected.

Clean mounting area of dust/debris. Wipe surface where new board will be installed.

Mount replacement board. Set into position and start retaining screws by hand.

Reconnect wires one by one. Reference photos to correctly match colors to labels.

Reinstall any removed panels or tubs. Secure with screws removed earlier.

Reconnect power and test functions. Run full cycle while checking board operation.

Inspect for proper function. Ensure machine is running as intended with new board.

Unplug the washing machine. Disconnect power to avoid electric shock.

Access the clutch. Remove the back service panel to access the clutch assembly.

Drain water lines. Empty any water lines attached to the clutch using a pan.

Disconnect clutch actuator. Detach the actuator rod, spring or motor from the clutch, if applicable.

Loosen mounting bolts. Use a socket wrench to loosen the mounting bolts on the clutch assembly.

Remove clutch. Carefully work the clutch off the drive shaft once bolts are detached.

Install new clutch. Slide the new clutch onto the drive shaft and align it into place.

Tighten mounting bolts. Secure the clutch by tightening the mounting bolts with a socket wrench.

Reconnect actuator. Reattach the actuator rod, spring or motor to the new clutch.

Replace service panel. Reattach the back service panel once done.

Restore power. Plug washing machine back in and test operation.

Check engagement. Verify the clutch engages properly when cycled on and off.

Unplug the washing machine. Disconnect power to prevent electric shock.

Open control panel. Unscrew the control panel on the washer to access interior.

Locate control board. The main control board is mounted to the cabinet interior.

Label wire connections. Note where each wire harness connects to the control board.

Disconnect wires. Detach all wire harnesses from the terminals on the control board.

Remove mounting screws. Use a screwdriver to remove screws securing control board.

Remove control board. Carefully detach old control board from the washer.

Install new control board. Align replacement board and reinsert mounting screws.

Reconnect wires. Attach all wire harnesses to proper terminals on new control board.

Close control panel. Carefully close and screw the control panel back on.

Restore power. Plug in washing machine and test operation.

Program control board. You may need to program the new control board if needed.

Unplug machine and open panels. Disconnect power and remove rear/bottom access panels for protected internal access.

Detach transmission belt. Remove belt from motor pulley and any transmission pulleys it engages.

Disconnect wiring harnesses. Unplug any electrical plugs connected to transmission controls.

Loosen mounting hardware. Remove retaining bolts or screws securing transmission to machine frame.

Extract transmission assembly. Ease transmission from mounts, wiggling side-to-side if stuck. Take care not to damage parts.

Clean transmission area. Wipe away debris from mounts where new unit will sit using dry cloth.

Install replacement transmission. Line up mounting holes and hand-start bolts to avoid cross-threading.

Reconnect wiring harnesses. Plug in any electrical connections removed earlier.

Replace transmission belt. Route belt correctly over pulleys, tensioning as per machine specifications.

Test operation. Run empty cycle and check for unusual noises before using for clothes washing.

Shut off power at breaker box. Disconnect power for safety before working.

Remove access panel or outer tub. Find securing screws to access pulley inside machine.

Locate idler pulley and belt. Pulley adjusts belt tension near spinning wash tub.

Loosen jamb nut on back of pulley. Turn nut counterclockwise to release bearing plate.

Slide off old idler pulley and belt. Twist components to separate as space allows.

Clean shaft and mounting surface. Wipe away dust where new pulley will attach.

Slide on belt and replacement pulley. Set pulley over shaft aligning set screw hole.

Tighten jamb nut against new pulley. Finger-tighten nut to hold pulley securely.

Set proper belt tension and tighten. Adjust pulley position then retighten lock nut.

Replace access panel or outer tub. Secure with screws removed earlier.

Reconnect power and check function. Run cycle to confirm pulley and belt working smoothly.

Disconnect power at breaker box. Turn off power for safety before working.

Remove access panel. Find securing screws and remove rear or bottom panel.

Locate idler pulley and lever arm. Pulley tensions belt via lever that pivots on a post.

Loosen pivot post nut. Turn nut counter-clockwise to loosen it from the end of the post.

Detach old lever arm from post. Gently slide arm off pivot post once nut is removed.

Clean pivot post and mounting surface. Remove any debris where new lever will attach.

Mount replacement lever arm onto post. Set arm in place over post and start pivot nut.

Tighten pivot post nut securely. Finger-tighten nut ensuring lever moves freely.

Reinstall any removed panels. Secure with screws removed earlier.

Reconnect power and test function. Run cycle to check idler pulley lever operation.

Readjust if needed. Loosen nut slightly to fine tune lever motion and belt tension.

Unplug the washing machine. Disconnect power to prevent electric shock.

Access the stator. Remove the back service panel to access the stator assembly.

Disconnect wiring. Detach the wiring harness leads from the stator windings.

Loosen mounting bolts. Use a socket wrench to loosen the bolts securing the stator.

Remove stator. Carefully detach the old stator assembly from the outer tub.

Install new stator. Align and mount the new stator assembly against the outer tub.

Tighten mounting bolts. Tighten the mounting bolts securely with a socket wrench.

Reconnect wiring. Attach the wiring harness leads to the terminals on the new stator.

Replace service panel. Reattach the back service panel.

Restore power. Plug in the washing machine.

Test operation. Verify proper functioning by running a test cycle.

Troubleshoot issues. If problem persists, check wiring connections on stator.

Disconnect power at breaker box. Turn off power for safety before working.

Remove outer tub, panel or belt access door. Find screws to access internal components.

Loosen motor mounting bolts just a few turns. Do not fully remove to avoid shifting components.

Slide off old belt from motor pulley. Twist and wiggle belt over edge of pulley.

Loosen set screw on pulley. Use an Allen wrench to release pulley from motor shaft.

Slide off old motor pulley. Gently wiggle pulley off shaft, may need to pivot components.

Clean motor shaft where new pulley mounts. Remove any debris from mounting surface.

Slide replacement pulley onto motor shaft. Set pulley in place over keyed end of shaft.

Tighten set screw on new pulley. Secure pulley to motor shaft so it does not rotate.

Loop new belt around replacement pulley. Reinstall any removed panels or accessories.

Test machine operation. Run cycle to confirm proper motor pulley replacement.

Unplug the washing machine. Disconnect power to avoid electric shock.

Access the clutch. Remove the back service panel to locate the clutch assembly.

Remove old bands. Carefully detach the old clutch bands from the pulleys and clips.

Clean pulleys. Use a wire brush to clean the drive and brake pulleys.

Install new bands. Loop the new clutch bands around the pulleys as directed.

Secure bands. Attach the guide clips and spring hooks to hold the bands in place.

Check alignment. Make sure the bands are properly aligned and taut.

Adjust band tension. Turn the tensioning springs to achieve the right tension on each band.

Replace service panel. Reattach the back service panel once done.

Restore power. Plug washing machine back in.

Test operation. Run washer through cycles to verify proper clutch engagement and braking.

Repeat tensioning. Recheck band tension and adjust springs again if needed.

Shut off water supply. Turn off valves where supply hoses connect to prevent flooding during repairs.

Disconnect hoses. Detach hoses from pump housing to access belt inside. Use pliers if needed.

Loosen retaining bolts. The water pump is usually secured inside the machine cabinet. Loosen bolts.

Tip out water pump. Gently rock or rotate the pump housing until it comes free from loosened bolts and can be lifted out.

Release belt tension. A bolt or lever typically tensions the belt around the pulleys. Loosen it.

Remove old belt. Slide the worn belt off one pulley, then the other to remove it fully from the pump compartment.

Position new belt. Loop the replacement belt over both pulleys so it sits correctly in the grooves.

Restore tension. Retighten the pump housing bolt or tensioning lever to firmly secure the new belt in place.

Refasten pump housing. Rebolt the water pump securely back inside the washer cabinet.

Reconnect hoses. Attach hoses to the pump inlet and outlet ports before turning water supply back on.