Washer Control Board

GE Washer m/n GTW460ASJ6WW would allow other fill levels, but when set to "super" it would never stop filling. Checked water inlet valve (by initiating a fill and unplugging the unit) to see if the inlet valve was sticking open, that was not the issue. Decided to replace the board even though it is a significant fraction of the cost of a new washer. Local appliance stores didn't have the board but APP did, and of course, they are open 24/7 while my local part stores have decided the weekend is... Read more

The washer would try to start. The door would lock, but then would get stuck in the phase of start-up where the drum needs to roll around (I assume so it knows what's in there). It would sit and think about it for a couple minutes and then give the error codes. I shut it off (sometimes had to unplug it and plug it back in), and it would take about 10 minutes for the door to unlock. After reading about fixes, I decided to dive in and try it (the washer is only 3 years old and I'm pretty... Read more

Replaced timer. Read more

I replaced the belt and the pump. It now works like it is new again! I am glad that I purchased the belt installation tool. It made replacing the belt very easy. I also purchased the Control Assembly which I did not install. It wasn't needed to repair the washer but I will keep it in case it is needed for future repairs. Of the 3 different web sites I looked at, AppliancePartsPros was the best price and the parts were at my house in 2 days. I will use AppliancePartsPros again if and when I need... Read more

I replaced the control board ordered from your website Read more

Searched the web and determined it was something called a noise filter. Ordered the part from ApplianceParts Pros. Received it in about 3 days, normal shipping. Replaced the part. Took about 15 minutes from start to finish. Problem solved. Cost less than $50. Read more

Based on symptoms it looked like the timer was not working. I did a web search to confirm this and found your web site. Entering the model number of the washer (Whirlpool) I found the timer and related information. This confirmed my diagnosis. I also looked at the video on how to change the timer. This was invaluable! The video saved me hours and probably a washing machine. I ordered the timer, it arrived as promised, I installed it per directions and the machine works... the video makes... Read more

I could not find specific online instructions for this job. Here are some tips. 1. Unplug the washer. 2. Unscrew the dial on the broken timer. 3. Gently pry up the thin plastic place-indicator plate (the thing with the arrow under the dial) with two flathead screwdrivers. 4. Unscrew the two hex screws holding the old timer in place. 5. Unscrew the phillips-head screws holding the console in place and flip up the console. 6. Remove the electrical connector from the bad timer, and remove the bad... Read more

I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more

This was the motor control board (also called the speed control board, motor control unit, or MCU in various places across the web). The repair was straightforward, except for two complications. First the old part was difficult to access in this model washer (Frigidaire Gallery Series front load washer). Instead of being easy to reach on the left side where there was space, it was sort of behind the actual motor on the right side of the housing. I spent some time trying to figure out... Read more

I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new... Read more

I diagnosed the problem, identified faulty parts, and replaced those components. Read more

• Timer will not advance

Based on an internet search, the likely problem seemed to be a bad timer-control switch because it would hum and click but not advance on a 17-year old washer. Repairman diagnosed the problem as a bad lid-switch-assembly and replaced it - problem solved. Now I need to return the Timer-Control. AppliancePartsPros was very quick to ship the Timer-Control and have a great return policy for an unneeded part. Read more

• Timer will not advance

I searched online and found Appliance Parts Pros to have the best price and an instructional video on how to replace this part. I've never done any type of repairs on a washing machine and figured I would give it a try. My washer is approx. nine years old and in good condition, and either I would repair this on my own or buy another. It took me about 30 min. to remove and replace the part, once this was completed I put the washing machine back into operation. Hurray!!!!!! did not have to spend... Read more

The repair guy was going to charge me upwards of $225 to replace the timer in my washer, if in fact it was the timer. I decided with Christmas just a month away that there had to be a better way. After speaking with one repairman, and then searching on the internet, I found out the problem with my Kenmore washer was probably the timer. Sears was going to charge me a lot to ship the timer and they wouldn't allow me to return it if after replacing it, it wasn't the problem. So, I got back on... Read more

• Timer will not advance

I replaced the timer Read more