12001957 Parts

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more

• Ice maker not making ice

I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy. Thanks so much for the great service and quick delivery !!! Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

We bought a new ice guard and installed it. It is working really good now. Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

I replaced the auger motor. You have to remove complete ice maker. Everything is just like help video to do except yoke dispenser. I watched video several times. Yoke will not just tap loose, after 30 minutes of tapping, I was using screwdriver to brace. I used a Dremel tool to cut part of shaft, came off easy then. After that, the repair went great. I have ice, I noticed motor I received was stronger. Parts came on time stated and worked great. I will order again on other repairs. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

Attached new handle with screws. Read more

• Ice maker not making ice
• Leaking

Order new valve Read more

Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

• Leaking

Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more

The removal of the ice bin and auger motor was easy but removing the auger from the shaft was another story. The auger was frozen to the shaft even after it sat out overnight. I carefully applied heat with a propane torch, directly on joint of the auger and the tip of the shaft, followed by a few drops of cold water. Once the shaft and auger cooled the auger separated easily. Putting the components back together was simple taking about ten more minutes. Read more

• Ice maker won't dispense ice
• Ice maker not making ice

Removed the broken ice enclosure tray, disconnecting and removing the motor and cube/crushed ice selector mechanism. Mounted the motor and selector mechanism to the rear of the new ice tray enclosure and installed the enclosure to the freezer compartment walls. Read more

I received the parts from parts pro within 3 days and everything fit perfectly nd all went well Thanks Parts Pro Wayne Mazur Joliet Il Read more