Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Burner won't spark or ignite? This cooktop igniter electrode creates the spark needed to light gas burners. Simple DIY fix in under 30 minutes.
This is a Montgomery Ward gas range made by Tappan. Parts are no longer offered for this appliance. So, I had to eyeball various ignitors to determine which one would work. I settled on the least expensive one and ordered two (Just in case there were "issues"). The parts arrived quickly but were not a simple drop-in replacement. The new ones were longer and smaller in diameter. I had to use the original bracket because it provided the electrical ground for the spark. I used a spring to... Read more
Gas burners won't ignite? A faulty spark module may be the issue. This part sends electrical current to igniters. DIY-friendly, takes minutes.
Watched repair video's to learn where parts were located. Put replacement in and it worked great! Read more
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Burner not heating or heating unevenly? This 8-inch plug-in coil element restores consistent heat to your range cooktop. Simple 5-minute replacement.
The burners and drip pans that I previously ordered fit this stove perfectly. It is so much better cooking on the cook stove with the burners laying properly. I'm very pleased. My only complaint is that I wish more parts were available for this old stove, I really love it! Read more
6-inch burner won't heat? This surface element coil restores steady heat for boiling and simmering. DIY-friendly replacement takes about 5-15 minutes.
Just took out old elements and then old pans. Replaced all 4 pans followed by 4 elements. Had to adjust element leads to get a secure level fit. Looked like a new range top when completed. The job was completed in less than 15 minutes. Read more
This replacement screw fastens panels, brackets, or trim inside your appliance. Swapping in a new screw restores a tight, secure fit and helps stop rattles, looseness, or misalignment caused by missing or damaged hardware.
Burner won't turn down from high or stays on? This infinite switch regulates heat to surface elements. Common DIY fix for overheating burners.
I immediately took the cooktop apart, found the bad part, and got the part number. I went online to AppliancePartsPros and typed in the model number, found the part and ordered it on a Sunday evening. The part arrived on Wednesday and I installed it that night and we were good to go! Read more
Secures the gas burner assembly to the cooktop base. Replace stripped, rusted, or missing screws to eliminate burner wobble and maintain proper alignment.
The constant cooking and age of the appliance I repaired corroded the housing attachment that holds the igniter in place to the burner. Also the screws that hold the burner in place to the stove cover were also corroded which caused the burner itself to not stay in place but fall into the stove. By using a screw driver, lift up on the sides of the stove cover to pop the clips that hold it in place. Use a block of wood to hold up the stove cover. On the model I worked on, the igniter removes... Read more
Replacement oven door seal creates a heat-tight barrier to maintain temperature and reduce heat loss. Replace if heat escapes or cooking times increase.
Looked up the part I needed...ordered and within a week, had a new door seal installed in minutes. Just snapped it in...ready to go. Read more
Secures panels and components in your range or oven. Replace if broken, bent, or missing to prevent shifting and reduce vibration noise. Confirm fit.
Appliance Parts Pros had my replacement parts and DIY repair videos, which made the repair a snap. Read more
This is a replacement refrigerant/line connection tube that links the service valve to the regulator line, restoring a sealed pathway for proper cooling system operation. It fits systems using a 3/8" tube connection. What it does:
After finding a model number on the range, I used the online parts diagram you provided to locate the part and part number. Ordering was super easy and the replacement was only two threaded fitting. It only took a couple minutes. Read more
Black end cap that covers and secures the outer end of your range handle. Replace this part when cracked, chipped, missing, or worn for a finished look.
Ordered a new handle and end caps. Had to re-tap the threads to take the original screws. Read more
Gas range burner cap sits on top of the burner head to direct gas flow and shape the flame. Replace if cracked, chipped, worn, or missing. Sold individually.
Replaced them with new ones. Read more
This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:
Body-side spacer for gas range door or lid hardware. Installs on cabinet side to set correct stand-off and alignment. Replace if cracked or missing.
Gas burner orifice that meters fuel flow to your cooktop or range burner. Replace if clogged, corroded, or when converting between natural gas and LP.
Found the right parts first time thanks Read more