Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Burner stuck on high or won't turn off? This burner control switch regulates heat settings. Moderate DIY repair—label wires before swapping.
If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more
Self-tapping screw used in range assembly. Features 8-18 thread size and 0.375 inch length. Also used in some washer models as cross-appliance hardware.
I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat. Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Fix a burned out or rusted grill element that won't heat properly. This electric grill coil restores even cooking and consistent searing on indoor grills.
The fan control switch is the panel-mounted switch that sends power to the appliance's fan motor. Replacing a worn switch restores reliable on/off control and proper airflow so the fan starts and stops when it should.
After looking at several YouTube videos that were only moderately helpful for my particular model, I disconnected the power at the breaker, disconnected the wires below the cooktop to the junction boxed lifted the whole unit out, including the fan assembly. I flipped it upside down and took off the screws holding the unit to the glass top. Although the new fan switch did not look the same as the original switch, the new switch does fit. The new switch did not come with a hex nut. The old hex... Read more
Color: black. It measures about 1 inch in diameter.
Remove unit, remove about 12 screw holding the top to the unit switch the tops reverse steps and done Read more
Replacement control knob for electric cooktop infinite switches. Restores precise heat selection. Replaces cracked, faded, or missing knobs.
Stamped metal retaining clip that secures screws to panels and trim. Replace if clip is bent, broken, or missing to properly fasten covers and components.
Replacement control knob for cooktop burner or fan settings. Restores easy turning and safe operation when original knob is cracked, broken, or worn.
I ordered a new knob, which arrived two days later, and popped it on. Read more
The stove is a CVG2420 Jenn Air 34" white stove top that is no longer made. I do not want to have to rebuild the island for a different stove, so I need to keep the old stove running. The trick to get into the control panel is that the top of the panel is attached to the gas piping frame by two Torx T-15 screws, one inside each of the center two light rings. Once inside the panel, it was very easy to remove the failed switch. The replacement switch was slightly larger than the original and... Read more
I bought new ones Read more