Abb252 Parts

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more

• Fridge too warm
• Noisy

I determined that the motor that drives the damper valve that allows cold air into the refer was noisy. I ordered the replacement part from AppliancePartsPro.com. It arrived within 3 days and I changed the units out, which took about 10 minutes total. All is quiet with the refer now. Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

Looked up parts based on fridge model number, watched videos, and replaced parts using just a few tools... easy. Parts came quick, well packaged. After 16 years, plastic parts deteriorate and break. The fridge was operating fine, but the drawers and covers were failing. Much cheaper to replace a few parts ($$-$$$) than buy a new fridge ($$$$). The new parts matched up exactly to old ones. The videos were very helpful, but not perfect... for the Crisper Frame, there was a structural metal... Read more

Ordered and installed new ones. Read more

Ordered and installed new ones. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Purchased replacement door gasket (seal). Pulled old gasket from its groove around door. Easily pressed the replacement gasket into the empty groove. Repair complete. Read more

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

Ordered the piece and put it in the refrigerator. Read more

Touch up paint Read more

Replaced It With New One Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

• Freezer not defrosting
• Freezer too cold
• Fridge too warm
• Freezer section too warm

After we moved into our new home, we realized that the freezer was very cold and the fins were frosting over, and the refrigerator wasn't cold. We had to take it apart and manually defrost it about once every 8 to 10 days. After research online, we found Appliance Parts Pros videos, which clearly explained how to fix it ourselves, a savings of at least $1,000 or more, since a new one of this size would have been in the arena of $1,200 to $2000. We ordered the three most likely parts to be bad,... Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more