Ade4brgs176tw01 Parts

Dryer lint filter traps fibers to maintain airflow and drying efficiency. Replace if torn, damaged, or missing to prevent lint buildup. Confirm fit.

Fix unresponsive or sticking control buttons with this panel-mounted push button switch. Restores reliable function activation. Straightforward repair.

Flat stationary rack that installs inside the dryer drum for air-drying shoes, hats, and delicate garments without tumbling. Replace if cracked or broken.

This seal kit restores a proper water-tight barrier in the washer's drive area to prevent leaks and protect bearings and motor components on 1992-and-newer units.

• Seals the drive shaft/tub interface to stop water migration
• Helps prevent bearing and motor damage from moisture
• Common leak symptoms: water under the washer, rust streaks at center post, noisy spin from moisture intrusion
• May also address oil/water contamination around the transmission area

• Disconnect power and water; move the washer to a stable, level work area
• Removal of agitator, inner tub, and drive components is typically required
• Inspect shaft and mating surfaces; clean and lightly lubricate as specified by service literature
• Use proper drivers/press tools; do not hammer seals into place

White plastic cover that snaps over the lint screen opening. Replace if cracked, broken, or missing to protect laundry from falling into the compartment.

Fix a dryer door that won't stay closed or pops open during cycles. This metal door strike secures the door and engages the safety switch. Easy DIY repair.

Clothes not drying or taking too long? This dryer blower wheel circulates air through the drum to dry clothes efficiently. Mounts on motor shaft.

Protective plate covering the rear outlet vent on your dryer. Replace if cracked, broken, or missing to prevent objects from entering the vent area.

Fix a dryer that won't start or respond when you press the button. This push-button switch restores reliable control panel operation in 15-30 minutes.

Covers the lint screen opening and directs airflow for efficient lint capture. Replace if cracked or missing to maintain proper airflow and prevent snags.

Dryer not powering on or overheating at the power connection? This terminal block assembly restores safe electrical connections. Moderate DIY repair.

This Outer Tub Gasket seals the outer tub assembly in your washer to keep wash water contained through every cycle. Replacing a flattened, cracked, or leaking gasket helps stop water on the floor and protects internal parts.

• Creates a watertight seal between outer tub components
• Helps prevent leaks during fill, wash, and spin
• Common symptoms: water under the washer; moisture at the tub seam; visible cracks or compression set on the gasket
• Restores proper sealing after service or disassembly

• Disconnect power and water supplies; move the washer for safe access
• Access the outer-tub seam per your model's service procedure; note gasket orientation
• Remove the old gasket and clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a brief test cycle to check for leaks

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle

Fix a dryer that won't respond to fabric setting changes with this 4-position fabric selector switch. Restores crisp detents and reliable selection.

Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.

Rotating drum assembly that tumbles laundry during drying. Replace if dented, rusted, or causing noise and uneven drying. Confirm fit with your model.