Adg4475tq1 Parts

Dryer lint filter traps fibers to maintain airflow and drying efficiency. Replace if torn, damaged, or missing to prevent lint buildup. Confirm fit.

Protective plate covering the rear outlet vent on your dryer. Replace if cracked, broken, or missing to prevent objects from entering the vent area.

Fix a dryer door that won't stay closed or pops open during cycles. This metal door strike secures the door and engages the safety switch. Easy DIY repair.

Flat stationary rack that installs inside the dryer drum for air-drying shoes, hats, and delicate garments without tumbling. Replace if cracked or broken.

Covers the lint screen opening and directs airflow for efficient lint capture. Replace if cracked or missing to maintain proper airflow and prevent snags.

Fix a dryer that won't start or respond when you press the button. This push-button switch restores reliable control panel operation in 15-30 minutes.

Clothes not drying or taking too long? This dryer blower wheel circulates air through the drum to dry clothes efficiently. Mounts on motor shaft.

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle

Dryer not powering on or overheating at the power connection? This terminal block assembly restores safe electrical connections. Moderate DIY repair.

This sensor monitors operating conditions and relays accurate feedback to the control so cycles run properly. Replacing a failed sensor helps restore correct operation and prevent erratic behavior or fault codes. What it does:

• Detects a specific operating condition and sends a signal to the control
• Helps the machine regulate cycle timing and performance
• Can cause error codes, cycles that won't start or advance, or intermittent shutdowns when failing
• Lead to inconsistent temperatures or sensing behavior depending on application

• 1 sensor

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Access the sensor; note wire positions and connector orientation
• Install the new sensor in the same location and orientation; seat connectors fully
• Clear any stored faults and run a test cycle per the tech sheet

Rotating drum assembly that tumbles laundry during drying. Replace if dented, rusted, or causing noise and uneven drying. Confirm fit with your model.

Fixes long dry times and temperature issues. This dryer thermostat regulates heat cycling to prevent overheating or underheating. Simple repair.

Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.

Fix a dryer that won't detect fabric dampness or stop at the right time. This moisture sensor base secures sensing contacts for accurate cycle timing.

This Outer Tub Gasket seals the outer tub assembly in your washer to keep wash water contained through every cycle. Replacing a flattened, cracked, or leaking gasket helps stop water on the floor and protects internal parts.

• Creates a watertight seal between outer tub components
• Helps prevent leaks during fill, wash, and spin
• Common symptoms: water under the washer; moisture at the tub seam; visible cracks or compression set on the gasket
• Restores proper sealing after service or disassembly

• Disconnect power and water supplies; move the washer for safe access
• Access the outer-tub seam per your model's service procedure; note gasket orientation
• Remove the old gasket and clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a brief test cycle to check for leaks

Fix a dryer that won't respond to fabric setting changes with this 4-position fabric selector switch. Restores crisp detents and reliable selection.