Chw9100lq Parts

Secures internal components in your laundry center. Replace if the retainer clip is cracked, broken, or missing to keep parts properly attached.

Fixes water leaks, slow drainage, or cycle interruptions caused by a cracked or clogged inner outlet hose. Straightforward replacement restores flow.

Inner door panel insert for front-load washer door assembly. Provides structural support and finished interior surface. Replace if cracked or damaged.

Covers the detergent dispenser drawer opening on your washer. Replace this plastic cover if it's cracked, broken, or missing to restore a clean appearance.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

Creates a watertight seal between the washer tub and cabinet. Replace if you notice water leaking during wash cycles. Verify fit with your model number.

Threads into the washer base to adjust height and stabilize the unit. Replace if cracked, stripped, or missing to eliminate rocking on uneven floors.

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

Washer won't start or shows electrical faults? A failed ground switch disrupts the safety circuit. This switch restores proper grounding for reliable operation.

This is a small hose that connects to the dispenser valve assembly inside the washing machine, directing water into the detergent or fabric softener dispenser. It ensures proper water flow to the dispenser during the wash cycle. Replace this hose if you notice leaking near the dispenser area, detergent not being flushed into the drum, or visible cracks and deterioration on the hose.

6-20 screw secures panels, brackets, and internal components. Replace stripped, missing, or damaged screws to restore proper fit and eliminate rattling.

Size: 8-18 x 1/2 inch.

Fixes washer that won't spin or agitate. Drive motor powers drum rotation during wash and spin cycles. Direct replacement for failed motors.

Control transformer that provides stable low-voltage power to the washer's control and user interface, ensuring reliable electrical signaling so cycles start and the machine operates correctly. What it does:

• Supplies the control board and user controls with the required control voltage.
• Restores power to displays, timers, and electronic controls when the transformer has failed.
• Common symptom: machine is dead, display is blank, or cycles won't start.
• Can cause intermittent power or control glitches before full failure.

• Disconnect power before servicing to avoid shock—follow lockout/tagout if required.
• Compare part number and mounting style to the original before installation.
• Handle terminals and wiring carefully; secure all connections and mounting hardware.

Washer won't spin or makes noise? This retaining nut secures pump and motor components. Common cause of leaks and wobbling. Basic tools needed.

Washer won't start, agitate, or spin? This motor control board regulates drive motor speed and direction. Restores proper wash and spin cycles.