Cwe23sp4mw2 Parts

This refrigerator switch actuator is the small linkage that presses a microswitch when the matching lever or door moves. Replacing a worn or broken actuator helps restore reliable response when you press the control or close the door.

• Engages the microswitch when the associated lever or mechanism is pressed
• Transfers motion from the user control to trigger the intended function
• Helps maintain proper alignment for consistent switch engagement
• Common clues it's failing: no response unless pressed hard, intermittent operation, or visible damage/missing piece

• Disconnect power to the refrigerator before servicing; also turn off the water supply
• Note the actuator's orientation and take a quick photo before removal
• Use small tools to release locking tabs; avoid prying against the microswitch or wiring
• After installation, manually press the actuator to confirm the switch clicks and responds before reassembly

This hinge-mounted refrigerator door stop limits how far the door swings open, protecting the cabinet and nearby walls from impact. Replace a cracked or missing stop to restore a controlled, factory door swing and prevent overextension.

• Mounts on the door hinge to control the door's opening range
• Helps prevent the door or handle from striking adjacent walls or cabinets
• Common symptoms: door opens past its normal range, broken/missing stop, visible wear at the hinge stop
• Often needed after an impact or when the original stop cracks from fatigue

• Disconnect power; turn off water to the door if applicable
• Support the door before loosening hinge fasteners; door removal may be required on some models
• Install the stop on the correct hinge location (right or left as required) and tighten hardware securely
• Verify door swing and clearance before fully loading shelves

This water filter cover assembly secures the refrigerator's water filter cartridge and helps direct filtered water into the dispenser/ice system, restoring proper filter seating and reducing the risk of leaks or poor water flow. What it does:

• Secures and retains the water filter cartridge in its housing
• Seals the filter area to help prevent water leaks around the filter
• Directs filtered water from the cartridge into the dispenser and ice system
• Helps restore proper filter engagement when the original cover is cracked or broken

• Turn off water supply and remove power to the appliance before servicing
• Remove the old cover and verify filter type/orientation before installing the new cover
• Push the cover into place until the filter seats and locks per the appliance design
• Re-check alignment and seals; replace damaged gaskets as needed

This deli control PCB with overlay replaces the electronic control used to operate a refrigerator's deli drawer, restoring user input and display functions so the drawer can regulate temperature and respond to controls. What it does:

• Provides the control logic and interface for the deli drawer functions and display
• Responds to user inputs from the overlay buttons or touchpad
• Sends/receives signals to the main refrigerator control for temperature management
• Commonly replaces a board when deli controls are unresponsive, display is blank, or buttons fail

• Disconnect power to the appliance before beginning any service
• Handle the board by edges and avoid touching circuit contacts; observe ESD precautions
• Reassemble trim and panels carefully; test functions before finishing

This replacement basket bottom assembly restores the lower basket's support and containment so stored items sit securely and the basket functions as intended. It's a direct-replacement part used when the basket floor is cracked, warped, or broken. What it does:

• Replaces the lower/bottom section of the basket to restore proper support and prevent items from falling through
• Stabilizes the basket so it rolls and seats correctly
• Stops rattling or sagging caused by a damaged or missing basket bottom
• Useful when the basket floor is cracked, split, or has broken support ribs

• Disconnect power to the appliance before any service; follow the manufacturer's safety instructions
• Remove the basket or access panel as needed to reach and replace the bottom assembly
• Inspect surrounding mounting tabs and rails for damage; replace any worn hardware for a secure fit
• Use basic hand tools.

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

The Dispenser Assembly is an OEM replacement part for GE refrigerators. This actuator is responsible for controlling the functions of the refrigerator's dispenser, allowing you to dispense water or ice.

A bad dispenser actuator assembly can occur due to wear and tear, damage, or component failure over time. If you notice symptoms such as the dispenser not responding to your input, loose or wobbly movement of the actuator, or the dispenser not dispensing water or ice properly, it may indicate a need to replace the actuator assembly.

Symptoms of a bad dispenser actuator assembly include:

• Unresponsive dispenser
• Loose or wobbly actuator movement
• Improper dispensing of water or ice

Restore your refrigerator's dispenser by replacing the faulty dispenser actuator assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This hinge cap is the small trim piece that covers your refrigerator door hinge. Replacing a cracked or missing cap protects the hinge from dust and restores a clean, finished look to the door area.

• Covers and protects the door hinge hardware from dust and debris
• Restores a clean, factory-finished appearance
• Helps keep the hinge area clear for smooth door movement
• Replace when the original cap is cracked, loose, discolored, or missing

• Disconnect power before servicing the appliance
• Support the door to prevent movement while working near the hinge
• Remove the old cap; align and press the new cap onto the hinge until fully seated; reuse the original fastener if your model uses one
• Verify the cap is secure and does not rub as the door opens/closes

This right-hand hinge top pin assembly supports and lets a refrigerator or freezer door pivot smoothly, restoring proper alignment and door operation. Use it to correct sagging, misaligned doors, or noisy pivoting. What it does:

• Provides the pivot point for the door's top hinge to enable smooth opening and closing.
• Restores proper door alignment to fix uneven gaps or doors that rub or stick.
• Helps eliminate grinding or squeaking noises from a worn or damaged hinge area.
• Supports the door weight to prevent further sagging or seal damage.

• Unplug the appliance or switch off power before servicing to reduce shock risk.
• Support the door when removing hinge fasteners to prevent dropping or damage.
• Use basic hand tools; follow OEM procedure for loosening/tightening hinge hardware and torque if specified by manufacturer.

This door case wiring harness connects the refrigerator door components to the main cabinet harness, restoring reliable power and signal routing for lights, dispensers, and sensors. Replaces a damaged or frayed harness to help resolve intermittent or non-working door functions. What it does:

• Transfers power and control signals between the door and cabinet wiring
• Restores operation for door-mounted lights, dispensers, and sensors affected by broken wiring
• Prevents shorts or intermittent failures caused by frayed or pinched wires
• Matches OEM routing and connector locations for a direct-replacement fit

• One door case wiring harness

• Disconnect power to the appliance before starting work to avoid shock or injury
• Handle connectors gently and route wiring per cabinet clips to avoid pinching
• Verify connector orientation and seating; secure any retained clips or screws

This left-hand door side assembly is the cabinet-mounted control panel support that secures the refrigerator's control and user-interface components for reliable operation and a finished door appearance. What it does:

• Provides the left-side mounting and housing for the fridge control panel and associated switches
• Keeps control components aligned and secured to the door for consistent operation
• Restores proper fit and finish when the original door-side control housing is cracked, loose or damaged
• Can help resolve symptoms like a loose control panel, rattling at the door edge, or exposed electronics

• One left-hand door side control assembly

• Disconnect power to the appliance before starting work to avoid electrical shock
• Remove door panels or trim as needed to access mounting screws; keep hardware for reassembly
• Align assembly carefully and tighten fasteners snugly but do not overtighten plastic threads

This right-side lower freezer drawer slide allows the freezer drawer to open and close smoothly and keeps the drawer aligned. Replaces a worn or damaged slide to restore stable drawer operation and prevent sticking or sagging. What it does:

• Guides and supports the lower freezer drawer for smooth in-and-out movement
• Replaces a broken, bent or worn right-side slide that causes the drawer to bind or drop
• Restores proper alignment so the drawer seals and closes evenly
• Works with the factory mounting points for a direct replacement

• Disconnect power to the appliance before removing drawers or service panels
• Remove the freezer drawer to access slide mounting screws; keep track of hardware
• Use appropriate hand tools; avoid forcing components to prevent damage