Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces damaged outer and inner door panels to restore appearance and maintain proper door alignment. Replace if panels are cracked, warped, or dented. Verify fit with your model number.
Replaced front panel and inner liner of door (kit), trap duct assembly, both bearing slides (gray and white), and drum front support bearing. Procedure is pretty much what one sees in the video clips. Exceptions in our case included: 1. The fact that our door latch¹ was on the front panel while the door strike² was on the door. The newer (replacement) design has the latch on the door and the strike on the front panel! 2. The new door did NOT have the door latch installed (as shown in the... Read more
Includes 12 screws. Size: 8-18 ab.
Ordered the cord through appliance parts pros, with additional screws and it works! Yay after waiting months and everywhere was out. Thank you. Read more
Covers unused hinge or mounting holes on refrigerator doors after reversing door swing. Replaces cracked, missing, or damaged plugs for a clean finish.
Replaces a worn, damaged, or misaligned dryer motor pulley. Guides the drive belt and transfers motor power to the drum for proper rotation.
Replaced belt, pulley with a 4 grove pulley. Pulley that was on there was a 3 grove pulley, Had to cut the old one off, Press on to shaft. Replaced rear drum bearing. Bearing was locked on with a snap ring. Access to it from a removable plate on the back side of dryer. Reset belt and idler puller by removing a long back plate on the bottom rear side of the dryer. None of this was shown in your Video. Read more
Dryer won't turn off or advance cycles? This mechanical timer controls cycle selection and transitions. Moderate DIY repair restores automatic shutoff.
I ordered a replacement timer, watched your video, and fixed it. Read more
Ceramic terminal insulator protects heating element electrical connections in dryers. Replace if cracked, broken, or missing to restore secure insulation.
Ordered parts. Watched video. Got parts in 3 days, made repairs. Took a little longer than expected but went well. Thanks Read more
Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.
The video was quite helpful with step by step instructions. I ordered a belt and idler pulley before dismantling assuming they were the issues. Belt was easy and fit fine but I did not realize the idler pulley was secured with a special fastener, push on cap nut, that would be damaged if removed. So I left it in place. Original pulley seemed fine so I reassembled the dryer. Restarted and of course the noise remained. I ordered the push on fastener and also the drum bearing as a precaution. ... Read more
Dryer top cover panel that forms the upper housing of your appliance. Replace if cracked, damaged, or missing to restore the cabinet appearance.
Dryer won't shut off in auto dry or only heats on one setting? This temperature switch restores proper heat level control. DIY-friendly repair.
Replaced temp switch Read more
Usually ships within 4 - 14 days
Replacement strain relief bracket that secures the power cord at entry point. Needed when bracket is cracked, broken, or missing to restore safe cord routing.
Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.
This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does
Ground strap assembly connects drum shaft to dryer frame for electrical safety. Replace if damaged, corroded, or causing startup squealing noise.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
Replacement drum assembly for dryers. Installs as the rotating cylinder that tumbles clothes. Needed when drum is cracked, damaged, or worn out.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.