Dle 0332 W Parts

Dryer stops mid-cycle or won't start? This door latch assembly secures the door to keep your dryer running. Simple 2-minute DIY fix for most models.

Replacement idler pulley that maintains tension on the drive belt. Install when the original is worn, cracked, or seized, causing belt slippage or noise.

Protective cover shields internal wiring and electrical terminals in your dryer. Replace if cracked, broken, or missing to prevent accidental contact.

Dryer won't start or overheats? A faulty high-limit thermostat breaks the heating circuit to prevent damage. Easy 5-10 minute DIY replacement fix.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

Spring-loaded belt tensioner that keeps the drive belt properly tightened. Replace if worn, seized, cracked, or causing squealing to restore smooth operation.

Hardware screws and nuts for installing a dryer side vent kit. Replace missing or stripped fasteners when reconfiguring exhaust outlet direction.

Replace missing or stripped taptite screws that secure panels and internal components. This thread-forming screw creates a tight hold to eliminate rattles.

The Incandescent Lamp is an OEM part for LG dryers. It serves as the interior light source for LG clothes dryers.

Causes of lamp failure relate to typical lifespan expirations, being accidently left on which shortens rated hours, or faulty sockets allowing moisture or other contamination to enter the connection points.

Symptoms of a burned out lamp include:

• Dark or completely unlit drum chamber interior
• Inability to fully inspect clothes during operation
• Difficulty monitoring dryer progress without supplemental lighting

This LG part is also compatible with some Kenmore models.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

The main PCB assembly is an OEM part for LG dryers. This control board is responsible for managing and coordinating the various functions and cycles of the appliance.

A bad main control board assembly can occur due to electrical issues, component failure, or other internal malfunctions. If you notice symptoms such as the dryer not starting, unresponsive buttons or controls, or error codes appearing on the display, it may be time to replace the main control board assembly.

Symptoms of a bad main control board assembly include:

• Dryer not starting
• Unresponsive buttons or controls
• Error codes appearing on the display

Restore the function of your LG dryer by replacing the faulty main control board assembly with this genuine OEM part. This OEM LG part can also be used on Kenmore/Sears appliances. 

Fix a dryer that won't turn off or won't start with this timer. DIY-friendly repair takes about 15 minutes. Match wires one at a time for easy install.

Specs: No.8X1/2 HEX WASHER HEAD

Precision mounting screw for dryers and laundry centers. Replaces missing, stripped, or damaged screws that secure panels, brackets, and assemblies. Restores stability.

Dryer won't start or stops mid-cycle? This door strike hook secures the door latch, engaging the switch so cycles can begin and run properly.

Fix a dryer door that won't stay closed or latched with this door lock assembly. Restores secure door closure for safe operation. Simple DIY repair.