Du1055xtdq1 Parts

Right-hand door hinge that restores proper door alignment and smooth operation. Replace if your dishwasher door sags, binds, or won't stay open. Verify fit.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Access panel covers the base of your dishwasher, concealing wiring and mechanisms. Replace if cracked, broken, or missing after installation.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Shield for dishwashers. Protects internal components from water and debris. Replace if cracked, broken, or missing to maintain proper coverage.

This is a small plastic or rubber fitting that secures the power cord where it enters the dishwasher's junction box or base. It prevents the electrical wiring from being pulled, kinked, or damaged by absorbing tension on the cord. Replace this part if it is cracked or missing, which can leave wiring exposed and vulnerable to damage during installation or use.

This dishrack replaces a damaged, rusted, or warped rack to restore smooth loading and secure support for dishes. A solid rack keeps items upright for better spray coverage, cleaner results, and helps prevent rust transfer and chipping.

• Holds and organizes plates, bowls, and cookware for proper spacing and spray access
• Provides stable support to reduce tipping and breakage during wash cycles
• Replaces racks with rust, broken wires, or bent/missing tines
• Can help resolve issues like rust marks on dishes and loading difficulties

• Disconnect power at the breaker before servicing
• Open the door; slide the old rack out—on some models, release rack stops to remove
• Transfer any reusable accessories from the old rack to the new rack if applicable
• Wear cut-resistant gloves; set the new rack on the rails and verify smooth movement and proper door closure

If your dishwasher won't start, stops mid-cycle, or has no display, the control board may have failed. Moderately difficult repair, typically 30 minutes.

Fix water leaking from under your dishwasher with this pump volute. Directs water flow and prevents leaks with integrated seal. 20-minute repair.

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Fix a dishwasher motor that hums or won't start. This run capacitor provides the phase shift needed for smooth motor operation. DIY repair in 30-45 min.

This is a rubber gasket that seals around the door vent opening on a dishwasher, preventing steam and moisture from escaping into areas where they can cause damage. It fits between the vent assembly and the inner door panel. Replace this gasket if you notice moisture or steam leaking from around the vent area, water dripping down the front of the door, or if the gasket appears cracked, warped, or deteriorated.

This is the inner door panel that forms the interior-facing surface of the dishwasher door, often including an integrated bottom door seal. It provides structural support for the door and helps contain water and steam within the wash compartment. Replace this panel if it is cracked, warped, corroded, or if the attached door seal is deteriorated and causing leaks around the bottom of the door.

Outer door panel for dishwashers. Installs on the front of the dishwasher door. Replace if scratched, dented, or to change color finishes.

Touch-up paint for restoring chips, scratches, and nicks on painted appliance surfaces. Covers minor cosmetic damage on exterior panels and finishes.