Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Usually ships within 4 - 14 days
The Roller Assembly is an OEM part for Frigidaire dishwashers. It includes the necessary rollers that allow the dishwasher rack to smoothly glide in and out of the appliance. Proper functioning of these rollers is essential for easy loading and unloading of dishes.
Over time, rollers can wear out or become damaged due to regular use or accumulation of debris. Causes of a bad roller assembly include wear from frequent use, damage from overloading the dishwasher rack, or debris buildup causing obstruction.
Symptoms of a bad roller assembly include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Replaced all 4 tray rollers - rolls great now Read more
I bought a replacement turbidity sensor and swapped it out. Very simple and straightforward. However there is one trick to be know. When I pulled out the bad sensor, drain water spilled from the hole and trickled into the motherboard housing! I then had to pull out the board and check it for damage. I left it in front of a box fan for 5 hours just in case. All is well. Read more
Replaced 3-sided gasket on washer & bottom gasket on door. 2.5 hours to do the former job. Most of this time spent cleaning old rubber & RTV glue out of groove. Followed instructions that came with new gasket. Wrapped edge of putty knife with 2 layers of electrical tape to avoid damaging gasket while pushing outside edge of gasket into groove. Latter job only took about 10 minutes. No glue involved. Had to spread groove ends a bit with screwdriver so that I could get the leading edge of the... Read more
Color: light gray. Measures about 3 inches high by 6 inches deep.
This is dishwashers circulation pump inlet connector. This part is what is responsible for transporting the water through the inlet. This is a component of the water circulation system of dishwashers. A new dishwasher circulation pump inlet connector may be needed if the part is physically cracked, broken, or damaged in any way. If there are problems with the dishwasher circulation pump, the dishes may not get as clean as they should. If any of these components get clogged, it will affect the operation of the unit. Be sure to unplug any electronic appliance prior to performing any care or maintenance on the unit or before replacing any parts.This is a genuine Frigidaire part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific dishwasher circulation pump inlet connector is compatible with dishwashers that are manufactured by Frigidaire, Kenmore, and Electrolux.
This replacement OEM part is a circulation pump motor assembly for dishwashers. The circulation pump motor distributes water to the spray arm to allow the dishwasher to properly do its job. Over time, the circulation pump motor can become overworked to the point of becoming inoperable. Luckily, replacing the pump motor is not as difficult a job as it might seem. To begin the repair, turn off the power supply and shut off the water supply valve. Remove the screws that secure the lower access panel. Disconnect the water supply line from the inlet valve. Then proceed to remove the mounting screws from the junction box cover. Take note of the wires' orientation. Remove the screws that hold the bracket. Disconnect the drain hose from the sink or garbage disposal. Open the dishwasher door and remove the mounting screws. Pull the dishwasher away from the cabinet and unsnap the covers from the hinge ropes. Disconnect the ropes. Remove the screws securing the upper door panel. Carefully tilt the dishwasher back and detach the fill hose from its retaining clip disconnecting the hose from the sump. Uninstall the circulation pump and align the pump with the seal and sump. Tighten the clamp and transfer the wires from the old pump to the new one. Proceed to reinstall the panels that were uninstalled.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand dishwashers.
Ordered part, removed defective unit, and installed new part. Read more
Replaced supply valve Read more
Restore proper heating and drying performance with this dishwasher heating element. It warms wash/rinse water and helps dry dishes at the end of the cycle so loads finish cleaner, drier, and on time. What it does:
After ordering a new heater and before disassembling the dishwasher to determine that it was in fact defective I found it was ok. After downloading the repair manual I saw that either the control assembly or the control pad on the door had to be at fault. I ordered both units from you and replaced the control assembly first and found that to be the fix. My first clue to the no heat problem was seeing small amounts of white film on the clean plates. I then noted the fine screen filter was... Read more
Fast fix - less than 1 minute. Did not have to remove the upper rack from dishwasher. Extended the upper rack and located the retaining clip holding the old spray arm in place. Released the old arm from the clip and snapped/slipped new one in place. New arm spins freely and dishes getting clean. Read more