Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Water Dispenser Valve is an OEM part for Frigidaire washing machines. This valve controls the flow of water into the washing machine during the wash and rinse cycles. It ensures that the correct amount of water enters the drum, contributing to efficient and effective cleaning.
Causes of a bad water dispenser valve can include mineral deposits or debris clogging the valve, wear and tear over time, or electrical faults that affect the valve’s operation.
Symptoms of a bad water dispenser valve include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
After tracing the water dripping back up through the inside of the washer I found the water dispenser inlet valve was leaking. I watched several videos to make sure I understood what was involved. I contacted a local parts company to get the part. I also searched online for the part. I found that AppliancePartsPros.com had it cheaper. I ordered late in the afternoon and it arrived the next day. It was fairly easy to installed and saved me a minimum of $99 "diagnostic" fee plus whatever the part... Read more
Creates a watertight seal between the washer door and tub to prevent leaks. Replace if you notice water leaking, tears, or mold buildup. Confirm fit by model.
Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more
Secures hoses and boots to pumps and tubs, preventing leaks. Replace if damaged, rusted, or unable to tighten. Confirm fit with your model number.
Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.
Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank Read more
Secures the shock absorber to the outer tub in your washer. Replace if the pin is broken, cracked, or missing to restore proper shock mounting.
With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more
This replacement spring restores the correct tension in the affected mechanism on your appliance, helping parts return smoothly and stay aligned. A fatigued or broken spring can cause loose action, noise, or improper engagement—this fixes it fast. What it does
Stabilizes the washer tub during spin cycles. Replace worn or broken rear shock absorbers to restore smooth operation and prevent drum contact with cabinet.
Drive belt transfers motor power to drum for tumbling and spinning. Replace when worn, stretched, or broken to restore smooth drum rotation. Verify fit.
Since I hadn't found the Tech Sheet for the washer (which there should be one inside the top cover) I simply thought I'd buy the drive motor (and a new belt, a.k.a "cheap insurance"). Installed the motor once I'd received it from AppliancePartsPros, the washer worked a couple of cycles then gave me the same "SrV CLL" message. I didn't know how to access the error codes on this model but found the info in the Tech Sheet, so I checked it and got an E53 code. Since I'd replaced the motor... Read more
Connects the outer tub to the drain pump in front-load washers. Replace if cracked, torn, leaking, or clogged to stop water damage and restore drainage.
Front shock absorber kit stabilizes the washer tub during spin cycles. Replace worn, loose, or broken dampers to restore smooth operation and stability.
I tore it apart using. YouTube videos to guide me and found the shocks were loose and floppy. I found the shocks in stock here and had them in my hand 2 days later for only $10 shipping! It runs great now! Read more
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Screens lint and debris from wash water as it exits the tub. Replace if damaged, missing, or clogged to restore proper draining. Verify fit by model number.
Bad drain pump impeller--installed new pump and filter you guys rock! right parts ,right price, on time! Read more
Fix a washer that won't start or run because the door won't lock. This door lock assembly secures the door during wash cycles. DIY-friendly repair.
Ordered new parts from appliancepartspris.com Read more
Seals washer tub halves to prevent leaks between drum sections. Replace if leaking onto floor or between shell halves. Confirm fit with model number.
Replaced gasket on drum Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.
Water was accumulating in the drawer pedestal, it was leaking from the front of the washer so I thought it was the front door seal. I also noticed it would leak even when the washer was not being used so I doubted it was the door seal. I googled the leak problems and watched a few videos which gave me confidence on washer disassembly. With the top panel off I noticed the leak coming from the water inlet assembly. Appliance Parts Pro’s had the part and replacement video and I replaced the part... Read more