Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fixes loose or wobbly timer controls by securing the timer assembly to its mounting bracket. Simple 5-minute repair restores proper cycle operation.
Purchased this Whirlpool dial and watched you-tube. Just popped off cover and put on new part. Second time replaced in 7 years. Works great! Read more
Includes suspension pads.
If your washer overfills, underfills, or won't advance cycles, the water level pressure switch likely failed. This DIY repair restores proper filling.
Removed upper cowling swapped out switch. Read more
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Washer only fills with hot water or won't fill at all? A faulty water inlet valve fails to control hot/cold mixing. Moderate DIY repair restores fill.
Hardware washer distributes load under fasteners to prevent loosening and reduce vibration. Replace when missing or damaged to restore secure fit.
Watched a video online, the project took about 20 minutes, went well, parts fit good, the video was very helpful in getting the wash machine up and running. Read more
Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do Read more
Replacement flexible hose that routes water inside your washer. Needed when original is cracked, kinked, worn, or leaking. Restores secure flow.
Added the extension drainage hose Read more
Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.
- Didn't see any other leaks in machine. No grinding transmission noise. Assumed seal on transmission shaft was bad, since it was a central leak down the rotor. It was a little more difficult to dissemble than the video showed, but not too bad. Got it all back together and seems to be working well. No leaks yet. Didn't need washer in parts diagram - was already on the transmission. Also the drain pump filter was not necessary, it can just be cleaned. Read more
This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.
Price Per Each
The balance ring clip fell between the drum and the plastic tub. I watched the step by step video, went out and bought a tub ring tool to remove the tub ring nut and did not find the clip. I disassembled the machine further reviewing the video again. In the end the machine must have been apart before and there were 3 clips missing total. I ordered 8 new clips and replaced them and reversed the procedure to reassemble the machine once again watching the video putting the machine back to better... Read more
Replacement console strap that secures the appliance control panel to the cabinet, restoring stable console alignment and preventing the control panel from shifting or sagging during use for safer, neater operation. What it does:
Size: 10-24 x 3/8 inch.
Replaced timer control unit, first time doing this. Read more
A cam sleeve that supports and guides the cam on its shaft to keep the cam-driven mechanism moving smoothly. Replacing a worn sleeve helps restore correct alignment and reduces binding or intermittent movement. What it does
The spin tube bearing and the cam sleeve needed to be replaced. Read more
5 foot. Package of 2.
We found the pump online at AppliancePartsPros.com for our model of Maytag. When we found the part, there was a video posted that was for our exact pump and washer. After watching it, we called Appliance Parts Pros to verify the part. The customer service representative was incredibly helpful and confirmed our diagnosis. We ordered the pump as well as hoses and clamps in case we needed them. We ordered them overnight delivery and the customer service rep said that we might not receive it... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.