Fafs4474lwo Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

Connects the detergent dispenser to the wash tub in your washer. Replace if cracked, leaking, or causing water damage to other components during cycles.

Seals washer tub halves to prevent leaks between drum sections. Replace if leaking onto floor or between shell halves. Confirm fit with model number.

Washer door boot seal creates a watertight barrier between door and drum. Replace if torn, moldy, or leaking during cycles. Verify fit with your model.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Fix E53 errors, no spin, or drum not moving. This motor control board restores washer operation. DIY repair in 45 minutes with our installation video.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Replacement mounting screw for washers and laundry centers. Secures components like pulleys, brackets, and panels. Replace if missing, stripped, or damaged.

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• Directs and regulates airflow through the appliance's air path
• Helps maintain proper pressure balance and efficient moisture removal
• Reduces the chance of lint or debris bypassing the intended ducting
• A cracked, warped, missing, or clogged vent can contribute to weak airflow, longer cycles, excess heat, or unusual noises

• 1 vent

• Disconnect power before servicing; allow hot components to cool
• Access the vent by removing the appropriate panel; note screw and clip locations
• Transfer any mounting hardware or seals from the old vent and ensure proper orientation
• Clear lint/debris from adjoining ducts before reassembly; test run to ensure smooth airflow and no rattling