Fdb710lcso Parts

The High Limit Thermostat is an OEM replacement part for Frigidaire dishwashers. It is a temperature control device located in the dishwasher's heating assembly that monitors water temperature levels during cycles. 

The high-limit thermostat plays a crucial safety role by automatically shutting off the dishwasher's heating element if water temperatures get too hot, preventing potential burns or damage. It ensures the dishwasher maintains the proper temperatures required for effective cleaning.

Symptoms of a bad high-limit thermostat include: 

• Incomplete or ineffective cleaning even on short cycles  
• Lack of hot water or intermittent hot water during cycles
• Strange smells or visible steam emitting from the dishwasher
• The heating element fails to activate when needed

This OEM Frigidaire replacement part is also compatible with some Electrolux, Westinghouse, and Kenmore dishwasher models. 

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This replacement latch secures the door closed so the appliance can operate correctly. Restores a positive close and consistent door recognition to help prevent no-starts and intermittent operation. What it does / common symptoms:

• Engages the strike to hold the door/panel closed
• Ensures the door-closed signal is made so controls can run
• Worn or broken latch may cause the door not to stay shut
• Unit may not start, show a "door" message, or stop if the door is bumped

• 1 latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch per model—typically behind the front panel or inner door liner
• Note and transfer any springs/clips from the original latch to the new one
• Verify smooth open/close and proper strike engagement before testing operation

The Dishrack Roller is an OEM part for Frigidaire dishwashers. This part ensures smooth and effortless movement of the dishrack in and out of the dishwasher. These rollers are attached to the sides of the dishrack, ensuring that it can glide easily without sticking or jamming, thus preventing damage to the dishes or the dishwasher itself.  

Causes of a bad Dishrack Roller can include wear and tear from regular use, damage from overloading the dishrack, or degradation of the roller material over time.  

Symptoms of a bad Dishrack Roller include:

• The dishrack sticking or struggling to move in and out
• A noisy operation when pulling the dishrack
• The dishrack tilting or becoming unaligned due to a missing or broken roller

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a circulation pump motor for dishwashers. It controls the main pump of the appliance.The pump is directly responsible for removing extra water from the dishwasher after use. When a dishwasher's circulation pump motor goes bad, the main indicator is usually leaking from the appliance. There will be a noticeable amount of water emerging from the bottom of the machine whenever the cycle is engaged. Unplug the dishwasher from its main power source and water hookup. Remove the dishwasher from its space in the counter. Remove all necessary entry plates to access the interior of the dishwasher. There is a metal bracket holding the current motor in. Unscrew the two screws that secure the bracket and remove this component. Remember which way the motor is oriented before removing it. Unplug the power cable connecting the motor to the dishwasher. Put the two new sealing rings on the new pump motor. Repeat these instructions in reverse to install the new part.This Frigidaire dishwasher circulation pump motor is a genuine OEM replacement part sourced directly from Frigidaire. The pump motor is sold individually. This part is compatible with Frigidaire, Kenmore, Westinghouse, and Gibson appliances.

Includes one sprayarm.

Set of 8 screws and washers.

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

Used on the upper rack track

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

This replacement screw secures appliance components so panels, brackets, and trim stay tight and properly aligned. Replace a missing, stripped, or corroded fastener to restore a solid fit and help stop vibration or rattling.

• Fastens components to the chassis or assembly for correct fit
• Helps maintain alignment and reduce movement and noise during operation
• Restores secure mounting when original hardware is missing, rusted, or stripped
• Typical symptoms: loose panel or handle, rattling noises, hardware backing out

• Disconnect power; if servicing a dishwasher, also shut off water
• Match the screw to the original location before installation
• Start threads by hand to avoid cross-threading, then tighten snugly without overtightening

Replacement white timer knob for oven or range controls, restoring a secure, easy grip for setting the timer and selecting cooking durations; designed to slip onto the control shaft for straightforward replacement. What it does:

• Provides a tactile grip to turn and set the appliance's mechanical or manual timer control.
• Restores positive engagement with the control shaft so settings stay set and adjustments feel firm.
• Common symptoms that indicate replacement: cracked, faded, loose, slipping, or a knob that won't turn.
• Intended for direct-replacement use on matching spline-style timer shafts; verify shaft shape before ordering.

• Disconnect power to the appliance (unplug or shut off breaker) before servicing controls.
• Remove the old knob by pulling straight off the control shaft; avoid twisting or levering on fragile bezels.
• Align the knob splines with the control shaft and push firmly until fully seated.
• If the knob does not fit easily, stop and verify spline pattern and part number to avoid forcing and damaging the control.