Fggf3032mfh Frigidaire Parts

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This ignitor/orifice assembly replaces the combined spark igniter and orifice holder for a gas surface burner, restoring fast, reliable lighting and proper flame. Replace it when the burner won't ignite, clicks repeatedly, or lights with delay.

• Directs gas through the burner orifice and positions the spark igniter for reliable ignition
• Common fix for a surface burner that won't light, has no/weak spark, or lights with delay
• Can help resolve unstable or uneven flame caused by a damaged or obstructed orifice
• Intended for the specific burner location and gas type specified by your model

• Disconnect power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, burner caps/heads to access fasteners
• Lift the top or burner deck as needed to reach the orifice holder; transfer the igniter lead and any brackets from the old assembly
• Reassemble, restore gas, check for leaks with soapy water, and verify burner ignition

This replacement valve controls gas flow to a cooktop/range surface burner, restoring smooth, dependable flame control through the burner knob. Replace a worn or leaking valve to improve safety and consistent burner performance.

• Regulates and shuts off gas to a single surface burner when you turn the control knob
• Helps resolve issues like a burner that won't light or won't adjust flame properly
• Can address a stiff/hard-to-turn knob or gas odor/leak at the valve stem area
• Supports steady, even flame when the original valve is worn or inconsistent

• Disconnect power and shut off gas supply before servicing
• Match the valve to the correct burner position per your model's parts diagram
• Transfer any required fittings/orifice from the original valve
• Use approved sealant where specified and check all connections with a leak-detection solution before use—never an open flame

This elbow is an angled connector used to route appliance tubing or hose in tight spaces. Replacing a cracked or leaking elbow restores a secure, sealed connection and proper flow, helping prevent kinks, drips, and water damage.

• Provides a compact change of direction for appliance tubing or hose
• Helps maintain proper flow and reduces the chance of kinking
• Seals the joint to help prevent drips and leaks
• Common symptoms: visible cracks, mineral staining or moisture at the joint, puddling under the unit, or reduced/intermittent water flow

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place towels/containers to catch residual water
• Prepare tubing with a clean, square cut; install per your model's connection style and avoid over-tightening compression fittings
• Restore water/power and check all connections carefully for leaks

This control panel replaces a worn, cracked, or cosmetically damaged console surface and restores clear button markings and access to controls. Fits the factory console opening and preserves the appliance's original look. What it does

• Provides the visible console surface that houses the control buttons and display
• Replaces cracked, chipped, or faded panels that make controls hard to read or use
• Restores a clean appearance and correct button/overlay alignment
• Helps prevent dirt and moisture from reaching the internal controls

• Disconnect power to the appliance before starting any work
• Handle the panel carefully to avoid scratching or bending during installation
• Installation typically requires removing console screws and any trim pieces; keep fasteners organized

This safety valve controls gas flow to the oven burner, opening only when the ignition system calls for heat. Replacing a weak or stuck valve restores reliable ignition and consistent oven temperatures for safe, dependable baking and roasting. What it does:

• Regulates and shuts off gas to the oven burner circuit
• Works with the igniter; opens only when proper current is present
• Fails closed to help prevent unlit gas from entering the oven
• Common symptoms may include: oven won't heat, intermittent heating, very long preheat, or a weak/unstable flame

• 1 safety valve

• Disconnect power and shut off gas supply before servicing
• Label and transfer all tubing and wires from the original valve one-for-one
• Support flare fittings with two wrenches; use thread sealant only on NPT threads (never on flare connections)
• After installation, restore gas and check every joint for leaks with an approved leak-detection solution

Size: 8-32t x 0.500 inch. Color: Black.

Restore proper oven operation with this electronic control board. It manages bake and broil functions and the display, helping bring back consistent heating and a readable clock/timer when the original control fails. What it does

• Directs power to bake and broil circuits based on user selections
• Controls oven temperature cycling using sensor feedback
• Drives the digital clock, timer, and status display
• Typical failure symptoms: dead or dim display, oven won't start or heat, unresponsive controls, intermittent operation, or error beeping

• 1 electronic control board assembly

• Disconnect power at the breaker before servicing
• Access the control behind the control panel; remove panel/console screws to reach it
• Move wires one at a time to the new board; photograph connections and reuse brackets/insulators as needed
• Handle by the edges and protect from static; for any required setup/calibration after installation

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This fan motor drives your oven's convection fan, circulating hot air for even, reliable cooking performance. Replacing a weak or noisy motor restores proper airflow to reduce hot spots and improve convection baking and roasting results. What it does:

• Powers the rear convection fan to move air across the oven cavity
• Promotes more uniform temperatures on multiple racks during convection cycles
• Helps the oven maintain stable heat during use
• Common symptoms: fan won't spin, intermittent or slow rotation, loud humming/scraping from the rear, uneven results in convection mode

• 1 fan motor

• Disconnect power to the range or wall oven before servicing
• Access may require removing the rear panel or the oven's rear cover; note wire locations for reassembly
• Transfer the original fan blade and mounting hardware to the new motor; handle sharp edges and avoid bending the blade
• Spin the blade by hand to ensure free movement before restoring power

This replacement panel restores your appliance's finished look and helps protect internal components. Replacing a cracked or loose panel eliminates gaps and rattles while keeping nearby trims or controls secured and aligned. What it does:

• Covers and shields internal areas, providing a clean, finished exterior
• Helps retain and align adjacent parts
• Restores proper fit when the original is cracked, warped, or discolored
• Common symptoms: broken mounting tabs, won't stay attached, vibration or rattling, visible gaps

• 1 panel

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; edges can be sharp
• Retain and transfer any screws, clips, or badges from the original panel
• Align tabs/holes and secure fasteners evenly—do not overtighten

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This control mounting hex nut secures the burner or oven control to the control panel, keeping the shaft stable so the knob turns smoothly and the switch stays properly aligned.

• Threads onto the control/infinite switch or thermostat bushing to fasten it to the panel
• Prevents the control from rotating or shifting when the knob is turned
• Replace if the original nut is missing, stripped, rounded, or corroded
• Common signs: loose or wobbly knob, switch spins in the panel, or misaligned knob indexing

• Disconnect power; for gas appliances, also shut off gas before servicing
• Pull off the knob and any trim; support the control body from behind the panel while removing/installing the nut
• Start the new nut by hand to avoid cross-threading; tighten snugly with the correct-size wrench—do not overtighten
• The control sits square in the panel and the knob operates smoothly before restoring power

The Handle is an OEM part for Frigidaire ranges. Crafted from durable heat-resistant metal, these handles provide safe, ergonomic access to oven interiors during cooking cycles.  

Prolonged exposure to elevated oven temperatures causes typical discoloration of painted finishes as well as looseness from load stresses reducing tactile control over years. Cooking convenience decreases without gripable surfaces.

Symptoms indicating handle wear include:

• Faded, chipped, or flaking handle finishes  
• Loose, rattling, or awkward movement from placement
• Deteriorating mounting attachments risking accidental falls

Replacing with this OEM Frigidaire handle restores tactile guidance into the cooking cavity. Compatibility also fits some Kenmore, Electrolux, and Gibson ranges renewing secure doorknob function through authorized maintenance. 

This replacement control knob restores a secure, easy-to-read interface for adjusting your appliance's settings. It lets you smoothly turn the control shaft to select heat or function when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the control shaft to turn functions on/off and adjust settings
• Provides a firm grip and clear pointer for accurate selection
• Common symptoms include a cracked knob, worn or missing indicator, loose/wobbly fit, slipping, or falling off
• Helps ensure the control returns to and indicates Off correctly when fully seated

• One control knob

• Allow the appliance to cool; for safety, disconnect power or shut off gas if applicable
• Pull the old knob straight off the control shaft—do not twist the shaft
• Align the keyed/flat side of the hub with the shaft and press the new knob on until fully seated
• Verify the pointer aligns with Off and turns smoothly; transfer any reusable insert/adapter from the original knob if your model uses one
• Some models use position-specific knobs; match markings and part number to your original