Fgid2468ufoa Parts

This strike is the receiver the door latch engages with to keep the door securely closed. A properly aligned strike helps the appliance recognize a closed door so cycles can start and run without interruption. What it does

• Provides the catch point for the door latch to secure the door during operation
• Helps align the latch for smooth, consistent engagement
• Ensures the door-closed switch can be activated so the unit can start
• Worn, bent, or broken strikes can cause the door not to latch, pop open, or trigger door-open errors

• 1 strike

• Disconnect power before servicing; follow manufacturer safety procedures
• Note the strike's orientation and any shims/spacers before removal
• Reuse existing mounting hardware unless your model specifies otherwise
• After installation, check alignment and the latch engages smoothly without force

This pulley is part of the dishwasher door balance system. It guides the door cable and spring so the door opens smoothly and stays controlled. A worn pulley can make the door feel heavy, drop open, or squeak.

• Routes the door balance cable between the hinge and spring to manage door tension
• Reduces friction for smooth, even door movement
• Helps prevent the door from slamming open or feeling excessively heavy
• Common symptoms: door drops or slams, won't hold a partially open position, squeaks or grinds near the base

• Disconnect power and turn off water supply before servicing
• Carefully relieve door spring tension; springs and cables are under load
• Pull the dishwasher forward to access the side frame area where the pulley mounts
• Note the cable routing before removal; install the new pulley and balanced door operation

Set of 8 screws and washers.

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This pulley guides the dishwasher door's balance cable so the springs can counterweight the door. Replacing a worn or broken pulley restores smooth, controlled door movement and helps prevent the door from dropping or feeling heavy.

• Guides the door balance cable/cord to maintain proper spring tension
• Helps the door open and close smoothly and evenly
• Visible cracks, wobble, or flat spots on the wheel indicate replacement

• Disconnect power and shut off water before servicing
• Remove the toe-kick to access the side spring/cable area
• Support the door and carefully relieve spring tension; note the cable routing through the pulley
• Install the new pulley in the original position and inspect related cable/link and spring for wear

This replacement bracket secures and supports an internal component in your appliance, restoring a stable mount and proper alignment. Install when the original bracket is cracked, bent, missing, or no longer holds the part firmly.

• Provides a rigid mounting point for the associated component
• Helps prevent shifting, sagging, vibration, or rattling from a loose mount
• Restores proper alignment for reliable operation
• Replaces a broken, warped, or missing bracket

• Disconnect power and, if applicable, shut off water/gas before servicing
• Note bracket orientation; transfer any spacers or hardware from the original
• Align bracket squarely and secure with appropriate fasteners; avoid overtightening
• Verify alignment and operation before reassembly

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

• Monitors water clarity/soil level during the wash
• Sends feedback to the control to adjust cycle length, rinses, and heating
• Failure can cause very long or very short cycles
• Can trigger sensor-related fault indications

• Disconnect power at the breaker and shut off water before servicing
• Access the sensor from the bottom near the sump; remove the toe panel if needed
• Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
• Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This cover is a protective panel used on Frigidaire appliances to shield and finish a specific assembly. Replacing a cracked or missing cover helps protect internal components and maintain proper routing or airflow so the unit operates as intended. What it does

• Shields internal parts from dust, moisture, and accidental contact
• Helps guide airflow or water within the assembly
• Secures adjacent components and restores a clean, finished appearance
• Typical symptoms: cracks, broken tabs, looseness/rattling, warping, or a missing panel

• 1 cover

• Disconnect power; if the appliance uses water, also shut off the supply
• Note fastener locations and transfer any clips or inserts from the original cover
• Inspect mating surfaces and any seals; replace damaged seals if needed
• Do not overtighten screws; verify clearances and wire routing before restoring power

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

The Dishwasher Manifold is an OEM part for Frigidaire dishwashers. It is a complex component that controls the flow of water through the various spray arms and nozzles within the dishwasher.

Causes can be mineral buildup or sediment that disrupts water flow, cracks or leaks in internal waterways, or damage from impact or unbalanced loads.

Symptoms of a bad Manifold include:

• Inadequate water pressure to one or more spray zones
• Blocked or clogged spray nozzles or arms
• Insufficient water flow for proper cleaning

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Panel is an OEM part for Frigidaire dishwashers. Located at the front of the dishwasher door, the control panel features buttons and displays that allow for the selection and monitoring of wash cycles. Printed electronic circuits distribute input signals to initiate the appropriate cycle settings.

Causes of a bad Control Panel can include cracked or damaged screens, non-responsive buttons, or failures of internal electronic pathways over time. 

Symptoms of a bad Control Panel include:

• Faulty or unreadable display screens  
• Random cycle activation without input
• Repeated error codes or flashing lights
• Physical damage or loose components  

This genuine OEM Frigidaire part is compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models as well.

Filter only. Fine filter not included.

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation