Frfs282laf1 Parts

This replacement electrical switch controls power to a specific function in your appliance. By opening or closing the circuit, it lets the selected feature turn on and off reliably when you actuate the control.

• Completes or breaks the circuit to start/stop its assigned component
• Restores responsive on/off or selector operation at the control
• Common failure symptoms: feature won't start or won't shut off, intermittent operation, loose/stuck actuator, or heat discoloration on the old switch
• Used in control, console, or door areas depending on model design

• Disconnect appliance from power before servicing
• Access the switch location per your model; remove knob/panel if applicable
• Photograph wire positions and note terminal labels (COM/NO/NC) if present; transfer wires one at a time to the new switch
• Secure mounting, ensure tight connectors, reassemble, restore power, and test operation

This refrigerator drain tube channels defrost water from the evaporator to the rear drain pan so it can evaporate. Replace a cracked, missing, or clogged tube to stop interior leaks and ice buildup.

• Routes defrost meltwater from the freezer drain to the condenser drip pan
• Helps prevent pooling under crisper drawers or water on the floor
• Common failure symptoms: water under drawers, ice sheet in the freezer bottom, recurring drain clogs or freeze-ups, dripping at the rear base
• Restores proper drainage when the original tube is brittle, split, or obstructed

• Disconnect power; pull the unit forward and remove the lower rear access panel
• Remove the old tube from the drain outlet and drip pan; clear any ice/debris with warm water—avoid sharp tools
• Seat the new tube fully on the drain outlet and position the outlet into the pan; verify flow by pouring warm water down the drain
• Restore power and monitor for leaks as normal defrost cycles resume

This factory screw secures components inside your refrigerator. Replacing a missing, rusted, or stripped fastener restores a tight, rattle-free fit for shelves, panels, and brackets so everything stays aligned, supported, and quiet.

• Fastens panels, brackets, or trim to the cabinet/liner
• Replaces damaged, corroded, or stripped hardware
• Helps resolve looseness, vibration, rattling, or misalignment
• Maintains proper support for shelves, covers, and assemblies

• Unplug the appliance; if working near water lines, shut off the water supply
• Match the new screw to the original; transfer any washers or spacers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving clip/insert is damaged, replace it to ensure a secure repair

The Door Switch is an OEM part for Frigidaire refrigerators. It is a basic on/off switch located inside the refrigerator door frame that controls power to interior lights. 

When the door is opened, the magnet inside activates the switch, illuminating LED lights inside the refrigerator and freezer compartments for convenience. This allows for ease of accessing and identifying items without additional switches.

Causes of a bad door switch can include normal wear over time, moisture exposure, or impact damage.

Symptoms of a bad door switch include:

• Lights not turning on when the door is opened
• Lights remaining on continuously even when the door closed  
• Inability to shut off lights manually 

Replacing the switch with a Frigidaire OEM part ensures the refrigerator's interior lights function properly based on the door position. It also helps optimize energy usage. This replacement is compatible with models by Electrolux, Gibson, Kelvinator, and Kenmore.

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

The Slide Assembly is an essential OEM component for Frigidaire refrigerator drawers. It provides smooth extension and retraction of covered storage bins during access.  

Symptoms of a faulty slide assembly include:

• Squeaking or rubbing noises coming from drawer rails   
• Difficulty smoothly pulling out covered bins
• Scratches or gouges visible along wear surfaces

Causes involve years of constant sliding stresses overwhelming lubrication, leading to increased friction. Without smooth gliding, premature deterioration of plastic drawer supports results.

This authentic OEM replacement is compatible with Frigidaire, Electrolux, and Kenmore models.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement bar is a direct-fit support component that helps hold and stabilize a refrigerator door or interior shelf assembly, restoring secure storage and preventing items from shifting or falling. What it does

• Provides structural support for a door or shelf ledge to keep stored items secure
• Replaces bent, cracked or broken bars that allow shelves or door bins to sag
• Helps stop rattling or movement from loose or damaged supports
• Restores proper alignment so shelves and bins sit flush and stable

• One replacement bar

• Disconnect power before removing refrigerator doors or interior components when necessary
• Remove affected shelf or bin to access mounting points
• Use basic hand tools; avoid overtightening fasteners to prevent cracking plastic parts
• Handle glass shelves and door bins carefully during removal and reassembly

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This control assembly replaces the appliance's electronic control module. Installing a new assembly can restore responsive controls and reliable operation when the original becomes unresponsive or intermittently fails. What it does

• Manages operating settings and coordinates functions of key components
• Interprets button/touch inputs and executes commands
• Drives indicator lights/display feedback
• Common symptoms include: unresponsive controls, blank or flickering display, random beeping or error codes, unit won't start or shuts off unexpectedly

• One control assembly

• Disconnect power to the appliance before servicing
• Use ESD precautions; handle the board by the edges and avoid touching circuitry
• Photograph wiring and transfer each connector and any brackets/overlay from the old part to the new one
• Ensure harnesses are fully seated and not pinched; some models may require a control reset or programming per the service manual

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

This replacement retainer clip secures trim, panels or small components inside your appliance to restore proper fit and reduce rattling. A simple, low-cost part commonly used where plastic or metal pieces need a secure hold. What it does:

• Holds panels, trim pieces or small assemblies in place to prevent shifting and vibration.
• Helps stop rattling, loose trim or components that don't stay seated.
• Keeps wiring or hoses routed and restrained when used as a harness/route clip.
• Suitable when original clip is cracked, broken or missing.

• Disconnect power to the appliance before beginning any work.
• Remove surrounding trim or panels gently to access the clip location; a trim tool or small screwdriver may be helpful.
• Clip installs by pressing into the mating slot or hole until it snaps; pliers may assist for removal/replacement.
• Verify correct orientation and fit by comparing the new clip to the old one before final reassembly.

The Slide Assembly is an OEM part for Frigidaire refrigerators. It secures crisper and pantry bins within the refrigerator interior, providing gliding functionality for easy access to stored items.

Causes of a bad slide assembly can include loose or broken mounting features, damaged rollers, or bent metal rails failing to guide bins smoothly. 

Symptoms of a bad slide assembly include:

• Difficulty removing or replacing crisper/pantry bins  
• Bins failing to close fully or stay securely in place
• Loud squeaking or grinding noises developing
• Dislodged mounting screws or loose mounting points

Replacing with this OEM slide assembly restores smooth operation. It is purpose-built to support everyday use without degradation.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before further component wear develops.

This control assembly replaces the electronic controls for your appliance, restoring reliable operation of the display and inputs. When the control fails, you may see a dead panel, unresponsive buttons, or erratic operation.

• Regulates and coordinates appliance functions based on user selections and feedback signals
• Interprets keypad/button commands and sends control signals to components
• Provides status indications or error feedback when applicable
• Typical symptoms: no display or power to controls, keys not responding, intermittent behavior, error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle circuit boards, ribbon cables, and connector pins carefully
• Photograph and label wire connections to ensure correct reassembly
• Transfer any mounting brackets or screws from the original part if needed