Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix ice dispensing issues caused by bent or dull crusher blades. This blade restores smooth crushed-ice flow. Quick DIY replacement with video guide.
I ordered (3) new replacement blades and received them in two days! Read more
Ice not dispensing or jamming? A worn auger can't move cubes from bin to chute. This rotating shaft restores smooth dispensing. Moderate DIY repair.
Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more
Front cover for your refrigerator's ice bucket. Replaces cracked, broken, or missing covers to keep ice contained and ensure proper dispenser seating.
I ordered the parts needed from you and they arrived quicker than promised. your chat person was extremely helpful in finding the correct parts needed. Great service Read more
Ice dispenser not dispensing or crushing properly? The drive cam transfers motor rotation to advance the ice dispensing cycle. DIY repair in 30-45 minutes.
This controller kit is the appliance's main electronic control. It reads inputs from the user interface and sensors to power and coordinate key components. Replacing a failed controller restores responsive controls and consistent, reliable operation.
Replaced controller and starter relay Read more
Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.
Removed the freezer shelves and back panel, evaporator coils were frozen with ice. Defrosted coil and removed defrost heater connectors, measured no continuity in the heater and ordered a replacement. Also discovered the aluminum retention strap was broken and the heater had slipped down in it's position, ordered and replacement strap. Re-installed new heater and strap per the video instructions, repair complete. Most difficult steps were drilling out the drain pan rivet and re-threading... Read more
This filter wrench is a ring-style tool used to loosen or tighten a refrigerator's water filter housing or canister. It provides extra leverage to free a stuck filter cup and helps ensure an even, secure reinstallation.
Replaced filter. Read more
Freezer drain tube that channels defrost water from the drain pan to the drip pan. Replace if cracked, leaking around the grommet, or causing floor leaks.
Replaced it Read more
Covers the service opening on your refrigerator. Replace if cracked, broken, or missing to protect internal components and maintain a clean appearance.
Freezer not cooling or running constantly? This compressor kit circulates refrigerant through the system. Advanced repair requires refrigerant handling.
Purchased a replacement COMPRESSOR. The compress or was a replacement for MFG. P/N 5304478809. The compressor was not an exact replacement. There was no port identification so the connections took a lot of time searching the net and then only the suction port was noted. I had to operate the compressor to be sure of the discharge port.The start relay on the original had no power plug as the new one did so had to improvise by cutting the wiring and adding 1/8 push on clips and then sliding on to... Read more
Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.
If your crushed ice comes out in large chunks or clumps, this fixed blade may be worn or broken. Works with the auger to deliver consistent crushed ice.
Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.
Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.
Replacement ice bin rail that supports and guides the freezer ice bin. Restores proper alignment when the original rail is cracked, broken, or worn.
Tank itself is not included in this kit. Kit includes tubing,screws & two John Guess fittings & instructions.
I watched your video on YouTube and it was super easy after that, thank you for making this video. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.