Frs262shb4 Parts

The Ice Chute Door Insulation is an OEM replacement part for Frigidaire refrigerators. It is installed on the ice chute door to prevent warm air infiltration and moisture buildup around the ice dispenser.

Causes may include compression or cracking of insulating foam/material from normal use stress. Spills exposing it to liquid are also damaging.

Symptoms of defective insulation consist of:

• Ice accumulating within the chute cover area
• Condensation visible on exterior chute surfaces
• Inefficient icemaker performance due to altered temperatures

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures panels, brackets, and other components in your appliance. Replace missing or stripped hardware to restore a tight, rattle-free fit and keep assemblies aligned the way the manufacturer intended.

• Fastens the designated component to the appliance cabinet or assembly
• Helps reduce looseness, vibration, and rattling
• Replaces missing, corroded, or stripped screws
• Supports proper alignment of panels, trim, and brackets

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to the original location; retain any reusable clips or washers
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten into plastic or thin metal

The Dispenser Lever is an OEM replacement part for Frigidaire refrigerators. This lever is a critical component of the refrigerator's water and ice dispenser system, located on the unit's exterior. It is designed to engage the dispenser when pressed, allowing for the seamless release of ice or water. 

Causes of a malfunctioning Dispenser Lever can include physical damage from impact, normal wear, and tear from repeated use, or a failure in the spring mechanism that could prevent it from returning to its off position. Maintaining this part in good working order is essential for its convenience.

Symptoms of a bad Dispenser Lever include:

• The dispenser fails to activate when the lever is pressed.
• The lever sticks in the pressed position or doesn't spring back.
• Difficulty in pressing the lever or it feels loose.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Dispenser Actuator is an OEM replacement part specific to Frigidaire refrigerators. It is the electronic component responsible for actuating and operating the ice and water dispenser. 

Symptoms of a bad ice dispenser actuator include:

• The ice or water dispenser not working or dispensing intermittently  
• No signal or responsiveness from the dispenser button
• Ice cubes were dispensed incorrectly in large clumps instead of individually

Causes of failure can be related to wear and tear of moving parts over time, failures in the small electronic circuit board, or damage to wiring affecting power delivery to the actuator motor. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Refrigerator Shelf is an OEM replacement part for Frigidaire side-by-side refrigerators. It is a durable glass surface that provides adjustable storage for various food items within the refrigerator compartment. 

Symptoms of a bad shelf include:  

• Cracks or chips in the glass that can collect bacteria
• Sagging or inability to properly support weight
• Broken mounting clips that cause the shelf to become loose

Causes of a bad shelf are typically normal wear and tear over time from repeated loading/unloading of items. Impact damage or overloading beyond weight limits can also cause failure.

Compatible with some Electrolux, Roper, and KitchenAid models as well, it ensures shelves support refrigerated goods as intended. 

The Upper Freezer Shelf is an OEM part for Frigidaire refrigerators. It provides additional storage space within the freezer compartment, allowing for better organization and more efficient use of the available space. This shelf fits securely in the upper section of the freezer, helping to separate and support various frozen items.

Common causes of a bad freezer shelf include heavy loads that cause cracking or breaking, warping from prolonged exposure to cold temperatures, or accidental impact.

Symptoms of a bad upper freezer shelf include:

• Visible cracks or breaks in the shelf
• The shelf not fitting securely in its designated slots
• Difficulty organizing or storing items due to an unstable shelf
• The shelf sagging under weight

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Fresh Food Temperature Control is an OEM part for Frigidaire refrigerators. This part regulates and maintains the temperature within the fresh food compartment, ensuring that your food stays at the desired temperature for optimal freshness.

Causes of a bad Fresh Food Temperature Control can include wear and tear over time, electrical faults, or damage to the control knob or internal components. 

Symptoms of a bad Fresh Food Temperature Control include:

• Inconsistent temperature within the fresh food compartment
• Food spoiling more quickly than usual
• The refrigerator running continuously or not running at all
• Difficulty adjusting the temperature setting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This torsion spring mounts in the dispenser to return the ice chute door/flapper to the closed position after dispensing. Replacing a weak or broken spring helps stop warm air leaks, frost, and ice clumping in the chute.

• Provides the closing force for the dispenser ice door
• Helps seal the ice chute to reduce frost and moisture intrusion
• Typical symptoms: ice door won't close fully, frost/ice buildup around the chute, cubes dropping after dispensing, or air leakage at the dispenser
• Replace if the spring is broken, deformed, or has lost tension

• Disconnect power before servicing; shut off water if working near the dispenser area
• Remove dispenser trim/bezel and control panel to access the ice door assembly; support wiring harnesses
• Note spring orientation and preload before removal; install the new spring on the same hinge posts in the same direction
• Manually cycle the flapper to ensure smooth return and a full seal before reassembly

The Freezer Temperature Control is an OEM part for Frigidaire refrigerators. This part regulates the temperature inside the freezer compartment, maintaining the desired cooling level to keep your frozen foods fresh and preventing freezer burn.

Causes of a bad Freezer Temperature Control can include electrical issues, sensor failures, or mechanical wear over time.

Symptoms of a faulty Freezer Temperature Control include:

• Freezer temperature fluctuations or inability to maintain a consistent cool temperature 
• Freezer becoming too warm or not cold enough 
• Frost buildup or excessive ice formation inside the freezer 
• The refrigerator running constantly or cycling on and off frequently

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Water Filter O-ring is an OEM replacement part for Frigidaire refrigerators. It is specifically designed to create a secure seal for the water filter, preventing leaks and ensuring that the filtration system operates effectively.

Causes for a malfunctioning Water Filter O-ring can include wear and tear from regular use, improper installation that leads to damage, or material degradation that affects its sealing capability.

Symptoms of a bad Water Filter O-ring include:

• Water leaks around the filter area
• Reduced effectiveness in water filtration
• The need for frequent filter replacements due to compromised seals
• Visible damage or wear to the O-ring

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Upper Hinge Bearing is an OEM replacement part for Frigidaire refrigerators. It facilitates the smooth and quiet opening and closing. By reducing friction at the hinge point, it ensures the door operates seamlessly and is less prone to wear over time.

Causes of a faulty upper hinge bearing include repetitive stress and wear from continuous door opening and closing over time. Exposure to moisture may accelerate bearing degradation.

Symptoms of a bad upper hinge bearing include:

• Squeaking or grinding noises emitted from the hinge area
• Difficult door operation requiring increased lifting force
• Potential misalignment compromising door seal integrity

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Includes service line.

This is an ice bin that is used on refrigerator and freezer units. The purpose of this part is to store the ice that has already been made so that it is ready for dispensing. The auger is included with this part, which is the component that drives the ice out of the freezer for dispensing. Over time, the white plastic material that the bin is made of may begin to crack or break due to exposure to extreme temperatures over time. If this is the case, it will need to be replaced. If the auger no longer functions, it could have become damaged and this part will also replace the auger itself. Wear work gloves when replacing this part.This ice bin is compatible with refrigerator and freezer units that have been manufactured by Kenmore Elite, Kenmore Pro, Kenmore, and Frigidaire. It is sold individually. This part is sourced directly from the manufacturer.

Note: Damper Control w/ two switches, if you need a Damper Control with one switch, order part# {AP5688411}

The evaporator fan motor mounting clip secures the freezer fan motor to its bracket, keeping it properly positioned to move air across the evaporator. A broken or missing clip can cause vibration, noise, or poor airflow.

• Holds the evaporator fan motor firmly in the freezer fan assembly
• Maintains proper fan blade alignment and clearance
• Helps prevent vibration, rattling, or scraping noises
• Common signs of failure: loose/wobbling motor, blade contact, inconsistent airflow

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer shelves/bins and the rear panel to access the fan assembly
• Release the old clip, position the motor, and snap the new clip fully into the bracket
• Ensure the fan spins freely and wiring is clear before reassembly and restoring power