Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Replacement mounting screws for washer cabinet panels, tub straps, and control assemblies. Sold in 12-pack. Replace stripped, rusted, or missing screws.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Seals the outer tub opening to prevent water leaks during wash cycles. Replace if leaking from top or gasket is damaged to restore clean performance.
Replaced the top cover which came with a new gasket. Easy to fix and works good. Saved me from buying a new machine. Read more
Secures control knobs onto shafts in top-load washers. Replace when knobs slip or fall off to restore proper fit and operation. Verify compatibility.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.
Took the old leveling legs out and put the new ones in Read more
Plastic housing that secures the drain solenoid to the pump assembly. Replace if cracked, broken, or missing to properly position the solenoid mechanism.
Viewed you video on Youtube.com and saw how easy it was to change out the triple water valve. Job completed and working like a charm now. Read more
Secures panels, brackets, and internal components in washers. Replace if missing, stripped, or damaged to restore proper fit and alignment.
I replaced the transmission, and a few other parts associated with the transmission. Read more
Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.
I ordered a new mode selector and new tub bearing. Upon disassembly, I noticed that the plastic outer tub had actually heated up around the tub bearing and tub seal area, such that the new tub seal did not fit tightly. I ordered a replacement outer tub, and reassembled all the new parts. During assembly, I installed the new tub seal upside down, but recognized it while re-watching the how-to video. I pulled the assembly back off and flipped the seal over, then reassembled it again. I also put... Read more
Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.
Fix scraping noise during agitation or poor cleaning with a new washer pulsator. Directs water flow and clothing movement. Takes about 10 minutes to replace.
Replaced the Coupling Pulsator, and the Pulsator (short spindle in the center of the washer). The only problem that I encountered was how to remove the short spindle in the center of the washer...my fabric softer is in the center and you need to open that, grab the middle and loosen by turning left. Once that is out you will use a 7/16th socket and remove the entire agitator. Most of the videos show that you pull that straight up to remove - not the short one. There is still a screw to remove.... Read more
Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.
Not hard when you have videos and a mechanical background....piece of cake.... Read more
12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.
The auger motor failed and wouldn't turn. I replaced the motor and it works without a problem. Make sure you dont throw away the motor boot or buy one if you don't have one. Otherwise, the temperature will freeze up the motor and lead to premature failure. Read more
Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.
Replace your worn, cracked, or missing washer control knob assembly. Restores secure grip and clear position indicators for cycle and temperature selection.