Gcwp1moww Parts

Includes 12 washers.

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

Outer tub cover kit that replaces a cracked or missing washer tub cover, protecting the inner tub and helping stop rubbing, noise and fabric snags. Restores proper tub clearance for smoother drum movement and quieter operation. What it does:

• Covers the outer wash tub to protect the inner tub and fasteners from contact and wear
• Helps stop rubbing, scraping or thumping sounds caused by tub-to-tub contact
• Reduces the chance of clothes catching between the inner and outer tubs
• Restores correct tub spacing so the drum spins without interference

• Disconnect power and water supply before starting any repair
• Access may require removing the agitator or inner tub and using basic hand tools
• Inspect mounting clips, seals and surrounding components and replace any damaged items
• Test the washer on a short cycle after installation to ensure proper fit and quiet operation

Secure your washer's drain hose with this drain hose strap. It keeps the hose positioned at the standpipe or laundry tub, helping prevent movement, dislodging, and messy leaks when vibration increases during drain and spin cycles.

• Secures the drain hose to a standpipe or utility sink, per installation guidelines
• Helps prevent the hose from backing out or spraying water during operation
• Reduces strain and kinking by keeping the hose routed in place
• Replaces a missing, cracked, or broken strap

• Unplug the washer and turn off water supply before starting
• Position the drain hose in the standpipe or tub and tighten the strap to secure it without kinking the hose
• Maintain the manufacturer-recommended air gap and hose height per your installation manual
• Run a quick drain/spin to ensure the hose stays secured and there are no leaks

This 10-18 Hi/Lo hex-washer screw is a direct-use replacement fastener for appliance panels, brackets and components. It restores secure mounting and helps stop loose trim, rattling or parts that shift during use. What it does:

• Secures panels, trim pieces, mounting brackets and similar components that use a 10-18 thread with a hex-washer head
• Restores proper fit where screws are missing, stripped, or corroded
• Helps eliminate rattling, vibration noise, and misaligned parts caused by loose fasteners
• Matches OEM head and thread style for a correct mechanical fit in specified locations

• Turn power or gas to the appliance off before working on electrical or gas-equipped units; unplug when applicable
• Use the correct sized hex driver or socket to avoid rounding the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging thin sheet metal
• If replacing multiple fasteners in a load-bearing area, replace all to ensure even fit and alignment

Size: 14-10 a trt 7/8 s.

Single-speed PSC motor that restores rotational drive to the appliance. Replaces a worn or failing motor to stop humming, no-spin or intermittent operation and helps return steady rotation when the rest of the drive system is serviceable. What it does:

• Converts electrical power into mechanical rotation to drive the appliance's rotating components.
• Common signs a motor needs replacement: humming, no rotation, slow or intermittent rotation, or unusual motor smells.
• Replaces a failed motor to restore normal, consistent rotation when the motor is the root cause.
• Designed for direct replacement where the same mounting and wiring are used.

• Always disconnect power to the appliance before beginning service.
• Follow the appliance service manual and wiring diagrams; label or photograph connections before removal.
• Support drum/assembly as required when removing or installing the motor; avoid strain on wiring.

This backsplash assembly replaces the rear panel on a freestanding range to restore wall protection and the appliance's finished rear appearance. It covers openings at the back and helps keep wiring and components protected and tidy. What it does:

• Covers the rear opening of the range to protect the wall from heat, grease and spills.
• Conceals wiring and access holes to help keep connections protected and out of view.
• Restores damaged, dented, rusted or missing rear trim caused by impacts, corrosion or wear.
• Provides the correct mounting surface for rear-mounted trim and components.

• Disconnect power to the appliance at the breaker before beginning any service.
• Remove the range from the wall if needed to access mounting screws; have a helper if the range is heavy.
• Hold the new backsplash in place and confirm alignment before tightening fasteners; retain original screws if replacement hardware is not supplied.

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

8-18 hi/lo 5/8

Size: 8-32 t. Includes 12 screws.

Includes 12 screws.

This hex nut overmold assembly secures appliance components while the molded sleeve protects surrounding surfaces and reduces vibration. It replaces worn or missing fasteners to restore a secure fit and help prevent rattling or movement. What it does:

• Provides a threaded fastening point for panels, trim, or internal brackets
• Molded overmold sleeve protects finishes and helps isolate vibration
• Restores secure mounting when a nut is stripped, missing, or loose
• Helps reduce rattling and movement of attached parts

• Disconnect power and follow appliance-specific safety procedures before starting
• Tighten by hand then snug with the appropriate wrench; avoid overtightening to prevent damaging the molded sleeve

This washer timer controls the appliance's cycle sequencing so the washer advances through wash, rinse and spin steps. Replacing a faulty timer restores proper cycle selection and automatic timing. What it does:

• Selects and advances wash cycles so the machine moves through wash, rinse and spin automatically
• Engages internal switches that power agitation, drain and spin functions
• Commonly replaced when cycles won't advance, the washer won't start, or it stops mid-cycle
• Works with the console controls to maintain correct timing and sequencing

• Disconnect power before servicing to avoid shock hazard
• Access may require removing the control console or back panel—retain fasteners and note wire positions
• Match connector locations and knob settings when reinstalling; test the washer through a complete cycle after install

This bracket secures the refrigerator door counterweight, helping the door stay balanced for smooth opening and closing. Replacing a damaged bracket restores proper weight support and prevents door sag or misalignment. What it does:

• Holds the counterweight assembly in place on the door to maintain balance
• Prevents the counterweight from shifting or falling during door movement
• Helps reduce door sag, sticking, or uneven closing when functioning correctly
• Works with the existing counterweight and mounting hardware to stabilize the door

• One bracket counterweight

• High-level task: typically accessed from inside the door panel; follow OEM disassembly steps
• Always unplug the appliance before starting work and support the door to prevent injury
• Keep all mounting screws and the counterweight assembly together for reinstallation

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit