Gdwt368vooss Parts

The Side Trim Gasket is an OEM part for GE dishwashers. This part provides a watertight seal along the sides of the dishwasher door. This part prevents water from leaking out during the washing cycle, ensuring your kitchen remains dry and safe from water damage. 

Causes of a bad Side Trim Gasket can range from natural wear and tear over time, which can degrade the gasket's material, to improper cleaning practices that may cause damage or allow buildup of debris, affecting the seal's integrity.

Symptoms of a malfunctioning Side Trim Gasket include:

• Visible leaks or moisture along the sides of the dishwasher door
• Deterioration or damage to the gasket, such as cracks, splits, or areas where it has become hard and lost its flexibility
• Difficulty closing the dishwasher door properly due to a misaligned or damaged gasket

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Pump and Motor Assembly is an OEM replacement part for GE dishwashers. It works to circulate water throughout wash and rinse cycles. The motor spins the integrated pump impeller to draw fresh water into the dishwasher and drain used water.

Causes of a bad pump and motor assembly can include mineral buildup on pump parts inhibiting water flow, worn motor windings reducing efficiency, or damage from freezing temperatures.

Symptoms of a bad pump and motor assembly include:

• Inability to fill or drain water from the dishwasher
• Abnormal noises coming from the motor area
• Leaks or water not circulating properly

This OEM part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Circulation Pump Impeller Kit is an OEM replacement part for GE dishwashers. This kit includes the necessary impeller components responsible for circulating water throughout dishwashing cycles. 

Causes of a bad circulation pump assembly include normal wear from continuous pump operation, along with mineral or debris buildup that can affect water flow.

Symptoms include:

• Inadequate or lack of water circulation within cycles
• Dirty dishes even after full cycles due to insufficient cleaning 

This OEM GE part is compatible with some Hotpoint, RCA, and select Kenmore models. 

The Upper Spray Arm Screw is an OEM replacement part for GE dishwashers. It is a component that secures the upper spray arm into place inside the dishwasher tub. The spray arm is responsible for distributing water above the top rack during wash cycles to help rinse and clean dishes.

Causes of a bad upper spray arm screw can include wear and tear from extended use that results in a loose or stripped screw. Failure to secure the spray arm properly affects washing performance. 

Symptoms of an improperly fastened upper spray arm include:

• Water not spraying properly from the arm jets
• Loose or rattling noises coming from inside the tub

This part is also compatible with Hotpoint, RCA, and select Kenmore dishwashers.

The Door Hinge Pulley is an OEM part for GE dishwashers. It is a critical component that assists in the smooth opening and closing of the dishwasher door by providing the necessary tension and balance through a pulley system.

Over time, the door hinge pulley can wear out or become damaged, leading to issues with the door's operation. Causes of a bad door hinge pulley include wear and tear from repeated use, buildup of dirt or debris, and accidental impacts that can damage the pulley or its mechanism.

Symptoms of a bad door hinge pulley include:

• The dishwasher door dropping or not staying open at the desired angle
• Difficulty in opening or closing the door smoothly
• Unusual noises when the door is moved
• The door feeling loose or unbalanced

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Pump Drain Assembly is an OEM part for GE dishwashers. This part effectively removes water from the dishwasher after the wash and rinse cycles, ensuring that your dishes are left clean and dry.

Causes of a bad pump drain assembly can include blockages from food particles or debris, wear and tear over time, or damage to the pump’s motor or internal components.  

Symptoms of a bad pump drain assembly include:

• Water not draining from the dishwasher
• Unusual noises during the drain cycle
• Standing water in the bottom of the dishwasher
• The dishwasher cycle not completing properly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower Spray Arm Assembly is an OEM part for GE dishwashers. This part is responsible for spraying water and detergent onto the lower rack of dishes during the wash cycle.

Causes of a bad Lower Spray Arm Assembly can include mineral buildup or debris clogging the spray holes, physical damage from impact or foreign objects, or wear and tear over time.

Symptoms of a faulty Lower Spray Arm Assembly include:

• Incomplete or ineffective washing of dishes on the lower rack
• Water not spraying evenly or not spraying at all from the lower arm
• Clogged or blocked spray holes
• Loud noises or grinding sounds during the wash cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Specs: B-16 HXW 1/2 SS

This middle spray arm hub secures the dishwasher's middle spray arm to the feed tube and lets it spin smoothly, helping deliver even spray coverage so dishes in the upper rack area get properly cleaned.

• Connects the middle spray arm to the water feed/manifold and serves as its rotating center
• Keeps the arm aligned so jets can distribute water evenly
• Wear or cracks can cause the arm to wobble, fall off, bind, or stop spinning
• Symptoms include poor cleaning on the upper rack and unusual noise from the arm area

• Disconnect power and water supply before servicing
• Remove the middle spray arm per your model's design and note its orientation
• Transfer and reuse any original screws, clips, or washers; install the new hub without overtightening
• Spin the arm by hand to ensure free movement before running a brief test cycle

This gasket trim seals the dishwasher door opening, helping contain moisture and steam during cycles. Replacing a worn, torn, or missing trim restores a proper barrier and helps prevent drips or condensation at the door area. What it does:

• Provides a moisture/steam barrier where the door meets the tub opening
• Helps protect the console and surrounding surfaces from escaping steam
• Cushions the door for a snug, secure close
• Common signs to replace: cracked, flattened, deformed, or missing trim; moisture around the door edges; visible wear

• 1 gasket trim

• Disconnect power and turn off the water supply before servicing
• Open the door and pull the old trim straight out of the channel
• Clean the groove; press the new trim fully into the channel without stretching
• Open and close the door to confirm even contact; reseat if needed

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

This part is a tactile control assembly kit that is used on a dishwasher. The tactile control assembly is the system that uses touch to make adjustments. For example, the buttons are connected to this tactile control assembly, and when the buttons are pressed, it is activated. A new tactile control assembly kit may be needed if the dishwasher keypad is entirely unresponsive when the buttons are pressed. If this is the case, the dishwasher will not be able to be used at all. The replacement process is relatively easy and takes anywhere from 30 to 60 minutes to complete. A screwdriver will be needed for the replacement.This tactile control assembly is a genuine General Electric part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific tactile control assembly is compatible with dishwashers that are manufactured by the General Electric brand.

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks